Terminal-block connection form端子排接入形式
Leads gather at terminal-block or wiring-board connection points, allowing circuits to be organized by terminal number.多根引线汇集到端子排或接线板连接位置，便于按端子编号组织不同回路。
Phoenix CompatiblePhoenix兼容组件
5.08mm 6-Pin Terminal Block Double-Ended Harness5.08mm接口 · 六针端子排双端线束
5.08mm 6-Pin Terminal Block Double-Ended Harness combines terminal-block connection form, terminal connection section, two-ended connection layout. Interface, circuit and installation data guide dimensions, material selection and sample review.5.08mm接口 · 六针端子排双端线束的结构重点包括端子排接入形式、端子接入部位、双端连接布局。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Terminal-block connection form端子排接入形式
- Terminal connection section端子接入部位
- Two-ended connection layout双端连接布局
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the 5.08mm 6-pin terminal block double-ended harness form as a starting point and confirm these design points against drawings and the actual equipment.以5.08mm接口 · 六针端子排双端线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Two-ended connection layout双端连接布局
Connection points sit at both cable ends, with the route arranged for equipment spacing and port orientation.线缆在两端设置连接位置，可结合设备间距和端口朝向安排整体走线。
Interface and function review接口与功能确认
Equal pitch does not guarantee cross-series mating相同间距不保证跨系列插接
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Phoenix terminal series, pitch and pole countPhoenix端子系列、间距与极数 | Define the interface through the family, pitch, pole count and matching header.完整系列、间距、极数与配套插座共同确定接口。 |
|---|---|
| Screw/spring clamping and conductor range螺钉或弹簧夹持及导体范围 | Select ferrules and processing for conductor construction and screw or spring clamping.螺钉或弹簧夹持按导体结构选择端头与加工。 |
| Plug direction, coding and matching header插拔方向、编码与配套插座 | Define plug direction and coding to prevent mixing equal-pitch families.明确插拔方向及编码，避免相同间距跨系列混配。 |
| Strip length, ferrules and torque requirements剥皮、冷压端头与扭矩要求 | Record strip length, ferrules and specified torque on the drawing.图纸记录剥皮尺寸、冷压端头和规定扭矩。 |
| Installation and operating boundary安装与使用边界 | Provide the mating reference, wiring view, conductor range, installation environment and required approval method.提供对插料号、接线视图、导体范围、安装环境及所需认可方法。 |
| Sample and release basis样品与放行依据 | Approve the interface schedule, workmanship sample and controlled inspection record before repeat production.重复生产前认可接口清单、工艺样品及受控检验记录。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Define the interface through the family, pitch, pole count and matching header.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，完整系列、间距、极数与配套插座共同确定接口。
Screw terminals and removable wire ends螺钉端子与可拆接线端
For screw-clamped connections, check conductor range, strip length and end preparation. Use the exact terminal documentation for tightening requirements. Select ferrules and processing for conductor construction and screw or spring clamping.螺钉夹持连接需核对导体范围、剥线长度和端头形式，紧固要求应来自准确端子文件。选配时，螺钉或弹簧夹持按导体结构选择端头与加工。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Define plug direction and coding to prevent mixing equal-pitch families.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，明确插拔方向及编码，避免相同间距跨系列混配。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Record strip length, ferrules and specified torque on the drawing.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，图纸记录剥皮尺寸、冷压端头和规定扭矩。
Equipment panels and circular interfaces设备面板与圆形接口
Start with the cutout, panel thickness, mounting direction and rear clearance. Coordinate contact arrangement and cable exit with the complete assembly view. Define the interface through the family, pitch, pole count and matching header.面板连接以开孔、板厚、装配方向和后方净空为起点；接点排列与电缆出口还需要对应完整总装视图。选配时，完整系列、间距、极数与配套插座共同确定接口。
Cabinet service and electrical checks控制柜检修与电气核对
Service work needs traceable circuits, contacts and wire labels. Agree the measurement method and link the results to acceptance records. Select ferrules and processing for conductor construction and screw or spring clamping.控制柜检修需要能追踪回路、接点与线号，约定测量方法后再把结果对应到验收记录。选配时，螺钉或弹簧夹持按导体结构选择端头与加工。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports phoenix compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕Phoenix兼容组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Define the interface through the family, pitch, pole count and matching header. Equal pitch does not guarantee cross-series mating.完整系列、间距、极数与配套插座共同确定接口。 相同间距不保证跨系列插接。
Define cable and installation conditions定义线材与安装条件
Select ferrules and processing for conductor construction and screw or spring clamping. Verify flexible-conductor and ferrule suitability.螺钉或弹簧夹持按导体结构选择端头与加工。 柔性导体和端头适配需核对。
Set processing and acceptance requirements确定加工与验收要求
Define plug direction and coding to prevent mixing equal-pitch families. Terminal-block ratings do not replace complete-circuit evaluation.明确插拔方向及编码，避免相同间距跨系列混配。 端子块额定不能代替完整回路评估。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can equal-pitch Phoenix interfaces be mixed?相同间距的Phoenix接口可以混用吗？
Equal pitch does not guarantee cross-series mating. Define the interface through the family, pitch, pole count and matching header.相同间距不保证跨系列插接。完整系列、间距、极数与配套插座共同确定接口。
Do all flexible conductors use the same ferrule?柔性导体一定要装同一种端头吗？
Verify flexible-conductor and ferrule suitability. Select ferrules and processing for conductor construction and screw or spring clamping.柔性导体和端头适配需核对。螺钉或弹簧夹持按导体结构选择端头与加工。
Can a terminal-block rating define the complete circuit rating?端子块额定能作为完整回路额定吗？
Terminal-block ratings do not replace complete-circuit evaluation. Define plug direction and coding to prevent mixing equal-pitch families.端子块额定不能代替完整回路评估。明确插拔方向及编码，避免相同间距跨系列混配。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the 5.08mm 6-pin terminal block double-ended harness. We can use them to review configuration and sample requirements.提供5.08mm接口 · 六针端子排双端线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。