Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Outdoor Cable户外电缆
BCC M415-M313-3F-300-VX8334-010 Circular Plug Sensor CableBCC M415-M313-3F-300-VX8334-010 · 圆形插头传感器连接线
BCC M415-M313-3F-300-VX8334-010 Circular Plug Sensor Cable combines circular connection end, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.BCC M415-M313-3F-300-VX8334-010 · 圆形插头传感器连接线的结构重点包括圆形连接端、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the bcc m415-m313-3f-300-vx8334-010 circular plug sensor cable form as a starting point and confirm these design points against drawings and the actual equipment.以BCC M415-M313-3F-300-VX8334-010 · 圆形插头传感器连接线的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Conductor and insulation selection导体与绝缘选配
Select conductors and insulation from circuit loads, diameter limits, bending and exposure. A material name does not replace ratings or validation results.从电路负载、外径限制、弯曲方式与环境条件选择导体和绝缘体系；材料名称不应直接代替额定参数或验证结果。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Outdoor temperature, sunlight and UV conditions室外温度、日照与紫外线条件 | Provide temperature range, sunlight and ultraviolet exposure conditions.提供温度范围、日照与紫外线暴露条件。 |
|---|---|
| Rain, standing water, burial or direct-burial use雨水、积水、埋地或直埋用途 | State rain, pooling water, conduit, burial or direct-burial duty separately.分别注明雨水、积水、穿管、埋地或直埋用途。 |
| Jacket material, weathering and media data护套材料、耐候与介质数据 | Tie jacket material and weathering data to the exact supplied model.护套材料与耐候数据须对应准确供货型号。 |
| Installation tension, abrasion and end sealing安装拉力、磨损与端头密封 | Record installation tension, abrasion points and sealing at both ends.记录安装拉力、磨损点及两端密封结构。 |
| Installation and operating boundary安装与使用边界 | Provide route, exposure, circuits, environment, connectors, sealing and required evidence.请提供路径、暴露、回路、环境、接口、密封与所需证据。 |
| Sample and release basis样品与放行依据 | Release records the exact construction, installation and agreed validation.放行记录包含准确结构、安装与约定验证。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Outdoor equipment and cable routes室外设备与电缆路径
Describe sunlight, rain, pooling water and retention on outdoor routes. Conduit installation and direct exposure need different material and acceptance requirements. Provide temperature range, sunlight and ultraviolet exposure conditions.室外路径应说明日照、雨水、积水和固定方式，穿管或直接暴露属于不同的材料与验收条件。选配时，提供温度范围、日照与紫外线暴露条件。
Equipment junction boxes and entry positions设备接线盒与入口位置
Define entry orientation, water-trap risks and service access at junction boxes. Record the seal-to-jacket combination separately. State rain, pooling water, conduit, burial or direct-burial duty separately.接线盒入口需要说明安装朝向、积水风险和检修空间；密封件与电缆护套的匹配关系单独记录。选配时，分别注明雨水、积水、穿管、埋地或直埋用途。
Exposed routing at rooftop equipment屋顶设备的外露走线
Coordinate supports, bends and entry positions at rooftop equipment. Select jackets and sealing boundaries for long-term exposure conditions. Tie jacket material and weathering data to the exact supplied model.屋顶设备走线需要协调支撑、转弯和接入位置，护套选型与密封边界要考虑长期暴露条件。选配时，护套材料与耐候数据须对应准确供货型号。
Equipment sensors and moving detection points设备传感器与移动检测点
Define signal type, mounting position and movement at sensor leads. Select shielding and grounding for the equipment noise environment. Record installation tension, abrasion points and sealing at both ends.传感器引线需明确测量信号、安装位置和运动范围，屏蔽与接地选择应对应设备干扰环境。选配时，记录安装拉力、磨损点及两端密封结构。
Enclosure entries and cable retention机箱穿线与入口固定
Match cable entries to actual diameter, panel thickness and fixing method. Keep jacket retention independent of the internal termination. Provide temperature range, sunlight and ultraviolet exposure conditions.线缆入口需匹配实际外径、板厚和固定方式；护套夹持与内部端接之间应保留独立的支撑路径。选配时，提供温度范围、日照与紫外线暴露条件。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. State rain, pooling water, conduit, burial or direct-burial duty separately.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，分别注明雨水、积水、穿管、埋地或直埋用途。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports outdoor cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕户外电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Provide temperature range, sunlight and ultraviolet exposure conditions. Outdoor suitability does not establish burial or immersion suitability.提供温度范围、日照与紫外线暴露条件。 户外适用不能自动转为直埋或浸水。
Match the actual installation duty匹配实际敷设工况
State rain, pooling water, conduit, burial or direct-burial duty separately. Weathering claims must identify tests and materials.分别注明雨水、积水、穿管、埋地或直埋用途。 耐候声明需对应具体试验与材料。
Confirm material and inspection documents确认材料与检验文件
Tie jacket material and weathering data to the exact supplied model. End ingress affects the complete cable system.护套材料与耐候数据须对应准确供货型号。 端头进水会影响完整电缆系统。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does outdoor suitability include direct burial and long-term immersion?户外适用是否包含直埋和长期浸水？
Outdoor suitability does not establish burial or immersion suitability. Provide temperature range, sunlight and ultraviolet exposure conditions.户外适用不能自动转为直埋或浸水。提供温度范围、日照与紫外线暴露条件。
What documents must a weathering claim identify?耐候声明需要对应什么文件？
Weathering claims must identify tests and materials. State rain, pooling water, conduit, burial or direct-burial duty separately.耐候声明需对应具体试验与材料。分别注明雨水、积水、穿管、埋地或直埋用途。
Why is water entry at cable ends a separate concern?端头进水为什么需要单独防护？
End ingress affects the complete cable system. Tie jacket material and weathering data to the exact supplied model.端头进水会影响完整电缆系统。护套材料与耐候数据须对应准确供货型号。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the bcc m415-m313-3f-300-vx8334-010 circular plug sensor cable. We can use them to review configuration and sample requirements.提供BCC M415-M313-3F-300-VX8334-010 · 圆形插头传感器连接线的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。