Angled cable exit弯式出线方向
The end transitions into an angled cable exit, allowing routing to turn beside the interface. Align its direction with the enclosure and neighboring ports.端头与线缆采用弯式过渡，便于在接口旁转向布线。弯头朝向应与机壳和邻近接口空间配合。
Coaxial Cable同轴电缆
BNC Right-Angle to SMA Right-Angle Coaxial Cable SetBNC直角转SMA直角同轴线组
BNC Right-Angle to SMA Right-Angle Coaxial Cable Set combines angled cable exit, bnc-form end, compact coaxial interface end. Interface, circuit and installation data guide dimensions, material selection and sample review.BNC直角转SMA直角同轴线组的结构重点包括弯式出线方向、BNC形式端头、小型同轴接口端。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Angled cable exit弯式出线方向
- BNC-form endBNC形式端头
- Compact coaxial interface end小型同轴接口端
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the bnc right-angle to sma right-angle coaxial cable set form as a starting point and confirm these design points against drawings and the actual equipment.以BNC直角转SMA直角同轴线组的结构形式为起点，结合图纸和实际设备确认以下设计要点。
BNC-form endBNC形式端头
The BNC-form end can be arranged around the equipment panel and cable route, with clearance for mating.BNC形式的连接端可配合设备面板和线缆走向布置，插接操作空间需保留。
Compact coaxial interface end小型同轴接口端
The compact coaxial-form end fits a compact interface layout. Arrange bends and end support to avoid pulling directly on contacts.小型同轴形式的端头可用于紧凑接口布局，线缆转弯与端头支撑需避免直接牵拉接点。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Signal path信号路径
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Coax type, center conductor and dielectric同轴型号、中心导体与介质 | Tie the exact cable model to centre conductor, dielectric and supplier data.准确型号须对应中心导体、介质和厂家数据表。 |
|---|---|
| Characteristic impedance, frequency and attenuation data特性阻抗、频率与衰减数据 | Specify impedance, frequency range and required attenuation data separately.分别规定阻抗、频率范围及所需衰减数据。 |
| Shield structure, coverage and jacket屏蔽层结构、覆盖与护套 | Record braid, foil, coverage construction and jacket material.记录编织、箔层、覆盖结构与护套材料。 |
| Diameter, bend radius and termination dimensions外径、弯曲半径和端接尺寸 | Match diameter, minimum bending conditions and termination dimensions together.外径、最小弯曲条件与端接加工尺寸成套匹配。 |
| Installation and operating boundary安装与使用边界 | Provide equipment ports, impedance, frequency band, signal or power, length, cable limits, route, environment and test evidence.请提供设备端口、阻抗、频段、信号或功率、长度、线缆限制、路径、环境与测试证据。 |
| Sample and release basis样品与放行依据 | Release records cable and connector part numbers, impedance, length, strip and termination controls, labels, environment and agreed electrical evidence.放行记录包含线缆与连接器料号、阻抗、长度、剥线和端接控制、标签、环境及约定电气证据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
RF interfaces and measurement boundaries射频接口与测量边界
Define ports, impedance, frequency range and measurement reference planes. Test records should correspond to the actual length and termination configuration. Tie the exact cable model to centre conductor, dielectric and supplier data.射频连接应明确端口、阻抗、频段和测量参考面，测试报告要对应实际长度与端接配置。选配时，准确型号须对应中心导体、介质和厂家数据表。
Antenna connections and environmental exposure天线端连接与环境暴露
Define equipment ports, retention and outdoor exposure at antenna connections. Confirm contact protection and cable-loss requirements separately. Specify impedance, frequency range and required attenuation data separately.天线端走线需说明设备端口、固定和室外暴露条件，接点防护与线缆损耗要求应分别确认。选配时，分别规定阻抗、频率范围及所需衰减数据。
Instrument inputs and coaxial measurement leads仪器输入与同轴测量引线
Match coaxial instrument leads to equipment ports, impedance and measurement frequency range. Define reference planes, length and shield termination. Select the cable and connector combination for the required loss and repeated-connection conditions.仪器同轴引线需匹配设备端口、阻抗与测量频段，说明参考面、线长及屏蔽端接。线缆与连接器的组合应对应项目所需的损耗和重复连接要求。
Coaxial construction and termination geometry同轴层结构与端接几何
Coordinate center conductor, dielectric, shield and connector dimensions. Set strip lengths and bend conditions from the exact cable type. Match diameter, minimum bending conditions and termination dimensions together.同轴端接需协调中心导体、介质、屏蔽层与连接器尺寸，剥线长度和弯曲条件应按准确线缆型号确定。选配时，外径、最小弯曲条件与端接加工尺寸成套匹配。
RF panels and cable ports射频面板与线缆端口
Match the connector mounting form and cable preparation at RF panel ends. Set mating and tightening-tool clearance from the actual assembly. Tie the exact cable model to centre conductor, dielectric and supplier data.射频面板端需要匹配连接器安装形式与线缆端接尺寸，插接和紧固工具空间以实际总装为准。选配时，准确型号须对应中心导体、介质和厂家数据表。
Oscilloscope and bench-instrument ports示波器与台架端口连接
At bench-instrument ports, define connector form, measurement reference plane and cable length. Provide retention and bending clearance for repeated connection. Specify impedance, frequency range and required attenuation data separately.仪器端口转接需明确连接器形式、测量参考面和线缆长度，端头固定与弯曲空间应便于重复连接。选配时，分别规定阻抗、频率范围及所需衰减数据。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports coaxial cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕同轴电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Tie the exact cable model to centre conductor, dielectric and supplier data. RG labels must match the exact manufacturer's specification.准确型号须对应中心导体、介质和厂家数据表。 RG标称必须对应准确厂家规格。
Match the actual installation duty匹配实际敷设工况
Specify impedance, frequency range and required attenuation data separately. Do not identify 50/75 ohms by color or diameter.分别规定阻抗、频率范围及所需衰减数据。 50欧与75欧不能以颜色或粗细识别。
Confirm material and inspection documents确认材料与检验文件
Record braid, foil, coverage construction and jacket material. Record raw-cable attenuation separately from terminated-assembly loss.记录编织、箔层、覆盖结构与护套材料。 原缆衰减与完整端接组件损耗分开记录。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can an RG name replace the exact cable specification?RG名称能代替准确线缆规格吗？
RG labels must match the exact manufacturer's specification. Tie the exact cable model to centre conductor, dielectric and supplier data.RG标称必须对应准确厂家规格。准确型号须对应中心导体、介质和厂家数据表。
Can size and colour distinguish 50-ohm and 75-ohm cables?粗细和颜色能区分50欧与75欧吗？
Do not identify 50/75 ohms by color or diameter. Specify impedance, frequency range and required attenuation data separately.50欧与75欧不能以颜色或粗细识别。分别规定阻抗、频率范围及所需衰减数据。
Is raw-cable attenuation equal to finished-assembly loss?原缆衰减等于成品组件损耗吗？
Record raw-cable attenuation separately from terminated-assembly loss. Record braid, foil, coverage construction and jacket material.原缆衰减与完整端接组件损耗分开记录。记录编织、箔层、覆盖结构与护套材料。
Start with your interface and installation requirements从您的接口与安装需求开始
Share cable specifications, conductor size, insulation and jacket requirements, installation conditions and target quantity for bnc right-angle to sma right-angle coaxial cable set. These guide material selection and sample review.提供BNC直角转SMA直角同轴线组的线材规范、导体截面、绝缘与护套要求、敷设工况及目标用量，我们据此梳理材料选配与样品确认事项。