Flat conductor arrangement扁平排列结构
The cable uses a flat arrangement, allowing compact routing around insertion direction, folds and end orientation.线缆采用扁平排列形态，可围绕插入方向、折转位置和端头朝向安排紧凑布线。
FPC / FFC AssemblyFPC / FFC组件
Camera Module FPC Extension Harness摄像头模组FPC延长线束
Camera Module FPC Extension Harness combines flat conductor arrangement, extension connection layout. Interface, circuit and installation data guide dimensions, material selection and sample review.摄像头模组FPC延长线束的结构重点包括扁平排列结构、延伸连接布局。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the camera module fpc extension harness form as a starting point and confirm these design points against drawings and the actual equipment.以摄像头模组FPC延长线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Extension connection layout延伸连接布局
The lead extends the connection to another position, with length, end orientation and fixing routed to the target location.连接线把接入位置延伸到另一端，可围绕目标位置定义长度、端头朝向与固定路径。
Interface and function review接口与功能确认
FPC and FFC are different manufacturing constructionsFPC与FFC不是同一制造结构
Installation and acceptance安装与验收
Equal pitch still requires matching thickness and contact orientation节距相同仍需匹配厚度和接触面
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| FPC/FFC type, pitch and circuit countFPC或FFC类型、节距与线路数 | Distinguish FPC from FFC before defining pitch and circuit count.先区分FPC或FFC，再确定节距与线路数。 |
|---|---|
| Same/opposite contact orientation and insertion direction接触面同向或反向及插入方向 | Define same-side or opposite-side contacts and the actual insertion views.明确两端接触面同向或反向及实际插入视图。 |
| Thickness, stiffener and exposed-contact length厚度、补强板与裸露接触长度 | Match total thickness, stiffeners and exposed-contact length.匹配总厚度、补强板和裸露接触长度。 |
| Connector locking, bend and installation space连接器锁止、弯曲和安装空间 | Define locking clearance, fixed folds and dynamic motion separately.将锁止空间、固定折弯和动态动作分别定义。 |
| Installation and operating boundary安装与使用边界 | Provide both endpoint references, pitch, circuits, contact-side views, tail dimensions, installed route, motion duty and inspection requirements.请提供两端接口、节距、回路数、触点面视图、尾端尺寸、安装路径、运动工况与检验要求。 |
| Sample and release basis样品与放行依据 | Approve the cable drawing, connector system, mating method, routing sample and electrical evidence before repeat production.重复生产前确认线缆图纸、接头体系、对插方法、布线样品与电气证据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Thin display cables and insertion boundaries薄型显示排线与插入边界
Check contact orientation, insertion length, stiffener thickness and latch access. Circuit count alone cannot establish mating fit. Distinguish FPC from FFC before defining pitch and circuit count.薄型连接需核对触点面方向、插入长度、补强厚度和锁止操作空间，不能仅凭线路数确定对插关系。选配时，先区分FPC或FFC，再确定节距与线路数。
Routing and retention in confined spaces狭小空间的布线与固定
Define bends, retention points and assembly order in confined spaces. Do not compensate for an incorrect interface direction or length with forced folds. Define same-side or opposite-side contacts and the actual insertion views.狭小空间布线需明确转弯、固定点和拆装顺序，不能用强行折线弥补接口方向或长度误差。选配时，明确两端接触面同向或反向及实际插入视图。
Routing and retention on moving equipment移动设备的走线与固定
Define travel, speed and retention at both ends of moving connections. Set separate targets and validation conditions for bending and torsion. Match total thickness, stiffeners and exposed-contact length.移动连接需明确动作行程、速度和两端固定，动态弯曲与扭转应分别设定目标和验证条件。选配时，匹配总厚度、补强板和裸露接触长度。
Display-module and control-board connections显示模块与控制板连接
Check insertion direction, contact orientation and frame clearance at display modules. Mark fixed folds on the assembly drawing. Define locking clearance, fixed folds and dynamic motion separately.显示模块连接需核对插入方向、触点朝向与边框空间，并将固定折弯的位置标入装配图。选配时，将锁止空间、固定折弯和动态动作分别定义。
Equipment control-board connections设备控制板连接
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Distinguish FPC from FFC before defining pitch and circuit count.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，先区分FPC或FFC，再确定节距与线路数。
Board service and module removal板卡检修与模块拆装
Keep latches and cable ends accessible for board service. Review removal paths and cable allowance alongside the controlled pinout. Define same-side or opposite-side contacts and the actual insertion views.板卡检修要保留锁扣与连接端的操作空间，拆装路径和线缆余量应与受控针脚表一起确认。选配时，明确两端接触面同向或反向及实际插入视图。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports fpc / ffc assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕FPC / FFC组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define termination and protection boundaries确定端接与保护边界
Distinguish FPC from FFC before defining pitch and circuit count. FPC and FFC are different manufacturing constructions.先区分FPC或FFC，再确定节距与线路数。 FPC与FFC不是同一制造结构。
Match dimensions and operating motion配合尺寸与使用动作
Define same-side or opposite-side contacts and the actual insertion views. Equal pitch still requires matching thickness and contact orientation.明确两端接触面同向或反向及实际插入视图。 节距相同仍需匹配厚度和接触面。
Verify processing and finished condition验证工艺与成品状态
Match total thickness, stiffeners and exposed-contact length. Dynamic flexing capability requires dedicated design verification.匹配总厚度、补强板和裸露接触长度。 动态折弯能力需专门设计验证。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Are FPC and FFC the same construction?FPC和FFC属于同一种结构吗？
FPC and FFC are different manufacturing constructions. Distinguish FPC from FFC before defining pitch and circuit count.FPC与FFC不是同一制造结构。先区分FPC或FFC，再确定节距与线路数。
Is equal pitch enough to confirm fit?相同节距是否足够确认适配？
Equal pitch still requires matching thickness and contact orientation. Define same-side or opposite-side contacts and the actual insertion views.节距相同仍需匹配厚度和接触面。明确两端接触面同向或反向及实际插入视图。
Are all flat flexible cables suitable for dynamic bending?薄型排线都适合动态折弯吗？
Dynamic flexing capability requires dedicated design verification. Match total thickness, stiffeners and exposed-contact length.动态折弯能力需专门设计验证。匹配总厚度、补强板和裸露接触长度。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the camera module fpc extension harness. We can use them to review configuration and sample requirements.提供摄像头模组FPC延长线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。