Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Oil & Gas Equipment Cable Assembly油气设备电缆组件
Circular Connector Pressure Sensor Cable圆形接头压力传感器连接线
Circular Connector Pressure Sensor Cable combines circular connection end, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.圆形接头压力传感器连接线的结构重点包括圆形连接端、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the circular connector pressure sensor cable form as a starting point and confirm these design points against drawings and the actual equipment.以圆形接头压力传感器连接线的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Conductor and insulation selection导体与绝缘选配
Select conductors and insulation from circuit loads, diameter limits, bending and exposure. A material name does not replace ratings or validation results.从电路负载、外径限制、弯曲方式与环境条件选择导体和绝缘体系；材料名称不应直接代替额定参数或验证结果。
Interface and function review接口与功能确认
Oil resistance does not establish explosion protection or gas tightness耐油不等于防爆或气密
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Equipment task, area classification and project standards设备用途、区域分类与项目标准 | Use the task, area classification and project standards to define review scope.用途、区域分类和项目标准决定审核边界。 |
|---|---|
| Oil, gas, pressure and temperature exposure油液、气体、压力及温度暴露 | Use actual fluids, gases, pressure and temperature for material conditions.实际油液、气体、压力和温度形成材料条件。 |
| Connector, seal and cable material list连接器、密封与电缆材料清单 | Review sealing, connectors and cable as a complete path.密封、连接器与线材作为完整路径审核。 |
| Shielding, grounding and explosion-protection responsibility屏蔽、接地与防爆责任边界 | Agree shielding/grounding separately from explosion-protection responsibility.屏蔽接地与防爆责任分开约定。 |
| Circuit and revision reference电路与版本依据 | Provide the equipment and installation-zone details, circuit and pin map, exact connectors and cable specification, fluids, temperature and mechanical exposure, sealing interface, quantity, required documents and project-specific inspection or qualification limits.请提供设备及安装区域资料、回路图与针脚表、准确连接器及线缆规格、接触介质、温度和机械工况、密封界面、数量、所需文件以及项目检验或验证限值。 |
| Sample and manufacturing configuration样品与制造配置 | We review the specified interfaces, materials and sourcing documents before sampling. The approved build can then be checked for dimensions, labels, termination and circuit continuity, with additional tests defined for the project.打样前审核指定接口、材料及来源文件。获认可的样品可检查尺寸、标识、端接及回路导通，并按项目定义附加试验。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Pumps and drive equipment泵与驱动设备
Define connections for media, thermal zones and equipment interfaces. Use the task, area classification and project standards to define review scope.根据介质、热区及设备接口定义电气连接。选配时，用途、区域分类和项目标准决定审核边界。
Field instruments现场测量仪表
Configure sensor supply, low-level signals and shields separately. Use actual fluids, gases, pressure and temperature for material conditions.传感器供电、低电平信号与屏蔽分别配置。选配时，实际油液、气体、压力和温度形成材料条件。
Process equipment and area-condition review工艺设备与区域条件评审
The project owner defines area conditions, media exposure and equipment documents before connectors, jackets and installation are reviewed. A context photo does not establish an explosion-protection rating.区域条件、介质暴露和设备文件需由项目方明确，再核对接头、护套与安装方式；场景照片不代表防爆等级。
Outdoor valve-bank interfaces室外阀组接口
Select connectors/jackets for temperature, rain and media exposure. Agree shielding/grounding separately from explosion-protection responsibility.温度、雨水与介质暴露共同影响接头及护套。选配时，屏蔽接地与防爆责任分开约定。
Equipment cabinet interconnects设备机柜互连
Allocate power, signals and earth separately with defined ports. Use the task, area classification and project standards to define review scope.供电、信号和接地分开布置并定义端口。选配时，用途、区域分类和项目标准决定审核边界。
Inspection and monitoring leads检修与监测引线
Do not assume monitoring leads have hazardous-area approval. Use actual fluids, gases, pressure and temperature for material conditions.监测连接不得默认具备危险区域使用资格。选配时，实际油液、气体、压力和温度形成材料条件。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports oil & gas equipment cable assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕油气设备电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Equipment task, area classification and project standards设备用途、区域分类与项目标准
Use the task, area classification and project standards to define review scope.用途、区域分类和项目标准决定审核边界。
Oil, gas, pressure and temperature exposure油液、气体、压力及温度暴露
Use actual fluids, gases, pressure and temperature for material conditions.实际油液、气体、压力和温度形成材料条件。
Shielding, grounding and explosion-protection responsibility屏蔽、接地与防爆责任边界
Agree shielding/grounding separately from explosion-protection responsibility.屏蔽接地与防爆责任分开约定。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does oil resistance mean explosion protection or gas tightness?耐油是否等于防爆或气密？
Oil resistance does not establish explosion protection or gas tightness耐油不等于防爆或气密
What evidence is needed for hazardous-area use?危险区域用途需要哪些依据？
Hazardous-area suitability requires specific approval evidence危险区域适用性需要具体批准证据
How should material compatibility be defined?材料相容性应怎样定义？
Material compatibility must identify actual media and conditions材料相容性需对应实际介质和条件
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the circular connector pressure sensor cable. We can use them to review configuration and sample requirements.提供圆形接头压力传感器连接线的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。