Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Industrial Equipment Harness工业设备线束
Circular-sheath equipment harness圆形护套多端子设备线束
Circular-sheath equipment harness combines circular connection end, terminal connection section. Interface, circuit and installation data guide dimensions, material selection and sample review.圆形护套多端子设备线束的结构重点包括圆形连接端、端子接入部位。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the circular-sheath equipment harness form as a starting point and confirm these design points against drawings and the actual equipment.以圆形护套多端子设备线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Terminal connection section端子接入部位
Leads use terminal-form ends at the connection points. Orientation, fixing and insulation coverage can follow the equipment assembly.引线以端子形式接入相应连接位置，可按设备装配方式安排端头方向、固定和绝缘覆盖。
Interface and function review接口与功能确认
Use identifiable installation datums for every branch分支在设备上有独立安装基准
Installation and acceptance安装与验收
Confirm separation and shielding for power and sensitive signals电源与敏感信号的间距及屏蔽路径需确认
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Equipment modules and interface allocation设备模块与接口分配 | Allocate connection points among cabinets, sensors, drives and auxiliary modules.按控制柜、传感器、驱动与辅助模块分配接入点。 |
|---|---|
| Branch endpoints, length datums and tolerances各支路起止点、尺寸基准及公差 | Measure trunk and branches from equipment fixing datums and record tolerances.从设备固定点量取主干与分支，并记录公差。 |
| Power and control circuit load table电源与控制回路负载表 | List power, control and sensitive-signal loads separately.分别列出动力、控制和敏感信号的电路负载。 |
| Fixing points, ducts and abrasion protection线束固定点、管槽与防磨布置 | Choose fixing and protection around ducts, openings and service routes.结合线槽、穿线孔与维护路径选配固定和防护。 |
| Circuit and revision reference电路与版本依据 | Confirm the equipment layout, connector or terminal-block models, pin or terminal numbers, voltage and current, cable path, ambient temperature, oil or abrasion exposure and maintenance method.需要确认设备布局、连接器或端子排型号、针脚或端子编号、电压电流、布线路径、环境温度、油污与磨损情况以及维护方式。 |
| Sample and manufacturing configuration样品与制造配置 | Engineering first reviews the drawing, BOM and routing constraints, then confirms materials and builds a sample. Branch dimensions, labels, connector orientation and continuity are checked against the approved sample before repeat production.先审核图纸、BOM和布线限制，再确认物料并制作样品；经确认的分支尺寸、标签、接口方向和导通关系将作为后续重复生产的依据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Industrial automation工业自动化
PLC cabinets, distributed I/O, conveyors, actuators, safety switches and assembly cells. Allocate connection points among cabinets, sensors, drives and auxiliary modules.PLC控制柜、分布式I/O、输送线、执行器、安全开关与装配单元。选配时，按控制柜、传感器、驱动与辅助模块分配接入点。
Machine tools & CNC机床与CNC设备
Spindle auxiliaries, sensors, lubrication, cooling, doors and internal control connections. Measure trunk and branches from equipment fixing datums and record tolerances.主轴附件、传感器、润滑、冷却、安全门和机内控制连接。选配时，从设备固定点量取主干与分支，并记录公差。
Packaging & processing equipment包装与加工设备
Motors, photoelectric sensors, heaters, valves, weighing modules and replaceable machine sections. List power, control and sensitive-signal loads separately.电机、光电传感器、加热元件、阀组、称重模块与可更换机组。选配时，分别列出动力、控制和敏感信号的电路负载。
Warehouse & material handling仓储与物料搬运
Conveyors, sorters, lifts, mobile modules, proximity detection and field communication. Choose fixing and protection around ducts, openings and service routes.输送机、分拣机、升降模组、移动单元、接近检测与现场通信。选配时，结合线槽、穿线孔与维护路径选配固定和防护。
Energy & environmental equipment能源与环保设备
Low-voltage controls, pumps, fans, sensors and auxiliary systems in storage, treatment and monitoring equipment. Allocate connection points among cabinets, sensors, drives and auxiliary modules.储能、处理与监测设备中的低压控制、泵、风机、传感器和辅助系统。选配时，按控制柜、传感器、驱动与辅助模块分配接入点。
Test & measurement systems测试与测量系统
Instrument panels, acquisition modules, test fixtures, internal interconnects and replaceable interface leads. Measure trunk and branches from equipment fixing datums and record tolerances.仪表面板、采集模块、测试工装、机内互连和可更换接口线。选配时，从设备固定点量取主干与分支，并记录公差。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports industrial equipment harness projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕工业设备线束的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Build from drawing or pin table按图纸或针脚表制作
We review circuit mapping, branch datum, connector direction, labels and installation constraints before a first article is released.在首件制作前审核回路对应、分支基准、接口方向、标识和安装限制。
Develop from an existing sample依据现有样品开发
A reference harness can be measured and mapped, but electrical function, mating interfaces and any hidden components still require customer confirmation.可对参考线束进行尺寸与回路整理，但电气功能、对插接口及隐藏元件仍需客户确认。
Connector and material alternatives接口与材料替代审核
When the original part is difficult to source, alternatives are compared by fit, terminal system, electrical rating, sealing and documented approval, not by appearance alone.原物料供应困难时，从装配、端子系统、电气额定、密封和书面批准等方面比较替代方案，不只比外观。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does industrial equipment harness mean one standard product?工业设备线束是一个固定产品吗？
No. It is a family covering cabinet, motor, sensor, I/O, sealed, internal and moving harnesses. The actual assembly is defined by your electrical and mechanical data.不是。它覆盖控制柜、电机、传感器、I/O、密封、机内及运动线束等多种结构，最终产品依据项目的电气与机械资料定义。
What can I send if I do not have a complete drawing?没有完整图纸时可以提供什么？
A sample, connector photos, mating-part references, pin table, equipment layout and required lengths can start the review. Unknown electrical functions must still be confirmed before production.可先提供样品、接口照片、对插型号、针脚表、设备布局和长度要求；不确定的电气功能仍需在生产前确认。
Can you make prototypes and small batches?可以做样品和小批量吗？
Yes. Prototype and small-batch builds can be used to check fit, routing and electrical mapping before a controlled repeat order.可以。可先通过样品或小批量确认装配、布线和电气对应，再转入受控的重复生产。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the circular-sheath equipment harness. We can use them to review configuration and sample requirements.提供圆形护套多端子设备线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。