Y-shaped breakoutY形分出结构
The breakout follows a Y-shaped route toward separate ends. Bend clearance and fixing can be arranged around the split.分出位置形成Y形走向，可把一处接入分向不同端头。安装时围绕分出点安排弯曲和固定。
Conxall CompatibleConxall兼容电缆组件
CMC-RC-Y Circular Connector Y-Branch HarnessCMC-RC-Y · 圆形接头Y形分支线束
CMC-RC-Y Circular Connector Y-Branch Harness combines y-shaped breakout, circular connection end, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.CMC-RC-Y · 圆形接头Y形分支线束的结构重点包括Y形分出结构、圆形连接端、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Y-shaped breakoutY形分出结构
- Circular connection end圆形连接端
- Plug-in connection end插接式端头
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the cmc-rc-y circular connector y-branch harness form as a starting point and confirm these design points against drawings and the actual equipment.以CMC-RC-Y · 圆形接头Y形分支线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Trunk and branch layout主干与分支
Locate trunk and branch datums from equipment fixing points. Allow room for mating, bends and servicing so branches do not transfer installation loads to contacts.以设备固定点确定主干和各支路的尺寸基准，预留插拔、弯曲和维护空间，避免支路把拉力传递到端子。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Exact Conxall series, shell size and contactsConxall具体系列、壳号与接点 | Specify the exact Conxall family, shell size and contact combination.指定Conxall具体系列、壳号和接点组合。 |
|---|---|
| Keying, locking method and gender插合键位、锁紧方式与公母 | Check keying, locking and contact gender as well as position count.针数之外核对键位、锁紧方式与接点公母。 |
| Cable entry, boot and molded construction线缆入口、尾套和模制结构 | Match entry, boot and molded construction to the actual cable.入口、尾套及模制结构按实际电缆匹配。 |
| Seal materials and full-mating test conditions密封材料及完整插合试验条件 | Define sealing materials and tests for the fully mated and installed assembly.按完整插合和安装状态确定密封材料及试验。 |
| Installation and operating boundary安装与使用边界 | Provide the complete family and part numbers, mating-face drawings, cable diameter, installation clearance and environmental conditions.请提供完整系列与料号、对插端面图、线缆外径、安装空间和环境条件。 |
| Sample and release basis样品与放行依据 | Build samples to approved drawings and BOM, then confirm mating, terminations, dimensions and agreed tests before release.按认可图纸与BOM制作样品，确认插合、端接、尺寸和约定试验后再放行。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Detachable circular connections可拆卸圆形连接
Check gender, keying, coupling and end-face views together. Equal contact counts do not replace confirmation of the exact series and part numbers. Specify the exact Conxall family, shell size and contact combination.圆形接口需要同时核对公母、键位、锁紧方式和端视图，针数相同并不能替代完整系列与料号确认。选配时，指定Conxall具体系列、壳号和接点组合。
Instrument inputs and measurement leads仪器输入与测量引线
Start measurement leads from signal type, input conditions and grounding. Select pairs and shields for the actual measurement range and noise target. Check keying, locking and contact gender as well as position count.测量引线以信号类型、输入条件和接地方式为起点，线对与屏蔽选择需要对应实际量程和噪声目标。选配时，针数之外核对键位、锁紧方式与接点公母。
Enclosure entries and cable retention机箱穿线与入口固定
Match cable entries to actual diameter, panel thickness and fixing method. Keep jacket retention independent of the internal termination. Match entry, boot and molded construction to the actual cable.线缆入口需匹配实际外径、板厚和固定方式；护套夹持与内部端接之间应保留独立的支撑路径。选配时，入口、尾套及模制结构按实际电缆匹配。
Equipment panels and circular interfaces设备面板与圆形接口
Start with the cutout, panel thickness, mounting direction and rear clearance. Coordinate contact arrangement and cable exit with the complete assembly view. Define sealing materials and tests for the fully mated and installed assembly.面板连接以开孔、板厚、装配方向和后方净空为起点；接点排列与电缆出口还需要对应完整总装视图。选配时，按完整插合和安装状态确定密封材料及试验。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Specify the exact Conxall family, shell size and contact combination.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，指定Conxall具体系列、壳号和接点组合。
External interfaces on portable equipment便携设备的外部接口
Consider handling, plug grip and cable bends together. Align the exit direction with the device position during use. Check keying, locking and contact gender as well as position count.便携设备连接要同时考虑操作手势、插头握持和尾部弯曲空间，线缆出口方向应与实际使用姿态协调。选配时，针数之外核对键位、锁紧方式与接点公母。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports conxall compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕Conxall兼容电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Specify the exact Conxall family, shell size and contact combination. Do not mix similar circular interfaces by pin count.指定Conxall具体系列、壳号和接点组合。 相近圆形接口不得按针数混配。
Define cable and installation conditions定义线材与安装条件
Check keying, locking and contact gender as well as position count. Original source models are search clues only.针数之外核对键位、锁紧方式与接点公母。 原始来源型号仅作检索线索。
Set processing and acceptance requirements确定加工与验收要求
Match entry, boot and molded construction to the actual cable. Ingress ratings must include specified mating and installation conditions.入口、尾套及模制结构按实际电缆匹配。 防护额定需包含规定插合及安装条件。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can similar circular interfaces be mixed by position count alone?相近圆形接口可以只按针数混配吗？
Do not mix similar circular interfaces by pin count. Specify the exact Conxall family, shell size and contact combination.相近圆形接口不得按针数混配。指定Conxall具体系列、壳号和接点组合。
Does one model string confirm the complete mating combination?仅有一个型号能确认完整插合吗？
Original source models are search clues only. Check keying, locking and contact gender as well as position count.原始来源型号仅作检索线索。针数之外核对键位、锁紧方式与接点公母。
Why do protection requirements need the complete installation state?防护要求为什么需要完整安装状态？
Ingress ratings must include specified mating and installation conditions. Match entry, boot and molded construction to the actual cable.防护额定需包含规定插合及安装条件。入口、尾套及模制结构按实际电缆匹配。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the cmc-rc-y circular connector y-branch harness. We can use them to review configuration and sample requirements.提供CMC-RC-Y · 圆形接头Y形分支线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。