Branched end layout分支端头布局
Conductors separate toward different ends, creating individual connection points. Branch lengths and directions can follow the equipment modules.导线向不同端头分出，形成独立接入位置。各支路可围绕设备模块分别安排长度与方向。
FCI CompatibleFCI兼容组件
D-sub Connector to Fine-Pitch Terminal Branch HarnessD-sub接头转细间距端子分支线束
D-sub Connector to Fine-Pitch Terminal Branch Harness combines branched end layout, d-sub interface end, end transition layout. Interface, circuit and installation data guide dimensions, material selection and sample review.D-sub接头转细间距端子分支线束的结构重点包括分支端头布局、D-Sub接口端、端头转接与组合。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Branched end layout分支端头布局
- D-Sub interface endD-Sub接口端
- End transition layout端头转接与组合
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the d-sub connector to fine-pitch terminal branch harness form as a starting point and confirm these design points against drawings and the actual equipment.以D-sub接头转细间距端子分支线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
D-Sub interface endD-Sub接口端
The D-Sub-form end allows equipment connection to be arranged around the mating face, fixing screws and rear cable route.端头采用D-Sub形式，可围绕插合面、固定螺钉和后部线缆走向安排设备连接。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Exact FCI series and full part numberFCI具体系列与完整料号 | Provide the exact FCI family, complete part numbers and mating-part details.提供FCI具体系列、完整料号及对插件信息。 |
|---|---|
| Wire-to-wire, wire-to-board or I/O format线对线、线对板或I/O接口形式 | Define wire-to-wire, wire-to-board or I/O mounting form separately.分别定义线对线、线对板或I/O安装形式。 |
| Contact arrangement, pitch and locking接点排列、间距与锁止 | Define contact arrangement, pitch and locking from interface drawings.针位排列、间距和锁止按接口图纸确定。 |
| Contact plating, wire size and assembly process端子镀层、线径与装配工艺 | Include contact plating, wire and processing requirements in the same BOM.端子镀层、导线与加工规范纳入同一BOM。 |
| Installation and operating boundary安装与使用边界 | Provide mating references, circuit drawing, dimensions and operating conditions.提供对插料号、回路图、尺寸及工作条件。 |
| Sample and release basis样品与放行依据 | Approve materials, samples and the released inspection plan before repeat production.重复生产前认可材料、样品及放行检验方案。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Provide the exact FCI family, complete part numbers and mating-part details.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，提供FCI具体系列、完整料号及对插件信息。
Equipment control-board connections设备控制板连接
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Define wire-to-wire, wire-to-board or I/O mounting form separately.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，分别定义线对线、线对板或I/O安装形式。
Cabinet data ports and cable routes机柜数据端口与布线路径
Keep port mapping clear while coordinating cable bends, termination support and module access. Validate protocol performance separately for the project. Define contact arrangement, pitch and locking from interface drawings.数据端连接需保持端口映射清晰，并协调线缆弯曲、端接支撑和模块检修路径；协议性能需另按项目验证。选配时，针位排列、间距和锁止按接口图纸确定。
Equipment panels and circular interfaces设备面板与圆形接口
Start with the cutout, panel thickness, mounting direction and rear clearance. Coordinate contact arrangement and cable exit with the complete assembly view. Include contact plating, wire and processing requirements in the same BOM.面板连接以开孔、板厚、装配方向和后方净空为起点；接点排列与电缆出口还需要对应完整总装视图。选配时，端子镀层、导线与加工规范纳入同一BOM。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Provide the exact FCI family, complete part numbers and mating-part details.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，提供FCI具体系列、完整料号及对插件信息。
Board service and module removal板卡检修与模块拆装
Keep latches and cable ends accessible for board service. Review removal paths and cable allowance alongside the controlled pinout. Define wire-to-wire, wire-to-board or I/O mounting form separately.板卡检修要保留锁扣与连接端的操作空间，拆装路径和线缆余量应与受控针脚表一起确认。选配时，分别定义线对线、线对板或I/O安装形式。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports fci compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕FCI兼容组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Provide the exact FCI family, complete part numbers and mating-part details. A brand abbreviation cannot replace series identification.提供FCI具体系列、完整料号及对插件信息。 品牌缩写不能替代系列识别。
Define cable and installation conditions定义线材与安装条件
Define wire-to-wire, wire-to-board or I/O mounting form separately. Check circuitry and housing for equal-pin-count I/O interfaces.分别定义线对线、线对板或I/O安装形式。 相同针数的I/O接口需核对电路与壳体。
Set processing and acceptance requirements确定加工与验收要求
Define contact arrangement, pitch and locking from interface drawings. Preserve part-number mapping when sources change.针位排列、间距和锁止按接口图纸确定。 供应来源变更需保留料号对应关系。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can the FCI abbreviation replace a family part number?FCI缩写能代替系列料号吗？
A brand abbreviation cannot replace series identification. Provide the exact FCI family, complete part numbers and mating-part details.品牌缩写不能替代系列识别。提供FCI具体系列、完整料号及对插件信息。
Can I/O interfaces with equal position counts be wired directly?相同针数的I/O接口能直接接线吗？
Check circuitry and housing for equal-pin-count I/O interfaces. Define wire-to-wire, wire-to-board or I/O mounting form separately.相同针数的I/O接口需核对电路与壳体。分别定义线对线、线对板或I/O安装形式。
How is the definition retained when the component source changes?供应来源变化怎样保持定义一致？
Preserve part-number mapping when sources change. Define contact arrangement, pitch and locking from interface drawings.供应来源变更需保留料号对应关系。针位排列、间距和锁止按接口图纸确定。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the d-sub connector to fine-pitch terminal branch harness. We can use them to review configuration and sample requirements.提供D-sub接头转细间距端子分支线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。