FAKRA-form connection endFAKRA形式连接端
The FAKRA-form end can be arranged around the equipment port, housing orientation and rear cable exit.端头采用FAKRA形式，可围绕设备端口、壳体朝向和后部出线安排连接。
RF & Coaxial AssemblyRF与同轴电缆组件
FAKRA to Miniature Coaxial Terminal Pigtail AssemblyFAKRA转微型同轴端子尾线组件
FAKRA to Miniature Coaxial Terminal Pigtail Assembly combines fakra-form connection end, end transition layout, terminal connection section. Interface, circuit and installation data guide dimensions, material selection and sample review.FAKRA转微型同轴端子尾线组件的结构重点包括FAKRA形式连接端、端头转接与组合、端子接入部位。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- FAKRA-form connection endFAKRA形式连接端
- End transition layout端头转接与组合
- Terminal connection section端子接入部位
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the fakra to miniature coaxial terminal pigtail assembly form as a starting point and confirm these design points against drawings and the actual equipment.以FAKRA转微型同轴端子尾线组件的结构形式为起点，结合图纸和实际设备确认以下设计要点。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Terminal connection section端子接入部位
Leads use terminal-form ends at the connection points. Orientation, fixing and insulation coverage can follow the equipment assembly.引线以端子形式接入相应连接位置，可按设备装配方式安排端头方向、固定和绝缘覆盖。
Pigtail connection form尾线连接形式
A lead section extends behind the connector, allowing length, further termination and support to follow the equipment connection.插接端后保留引线段，便于按设备接线位置确定长度、后续端接与支撑。
Trunk and branch layout主干与分支
Locate trunk and branch datums from equipment fixing points. Allow room for mating, bends and servicing so branches do not transfer installation loads to contacts.以设备固定点确定主干和各支路的尺寸基准，预留插拔、弯曲和维护空间，避免支路把拉力传递到端子。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Coaxial cable type, impedance and frequency range同轴电缆型号、阻抗与频率范围 | Define the transmission basis from coax type, impedance and frequency.同轴型号、阻抗与频率共同确定传输基础。 |
|---|---|
| End connector series, gender and reverse polarity两端连接器系列、性别与反极性 | Check series, gender and reverse polarity at the center contacts.系列、公母及反极性按中心接点核对。 |
| Length, insertion-loss and return-loss conditions长度、插损与回损验收条件 | Specify measurement bands and methods for loss and length.插损、回损与长度写明测量频段和方法。 |
| Crimp tools, strip dimensions and bend radius压接工具、剥线尺寸与弯曲半径 | Match stripping, crimping, ends and bend limits to the cable.剥线、压接、端头与弯曲配合具体电缆。 |
| Circuit and revision reference电路与版本依据 | Provide both mating interfaces, standard or reverse polarity, impedance, frequency band, power and DC bias, maximum insertion loss and return-loss/VSWR target, cable length and phase requirement, shielding or PIM requirement, routing and bend radius, panel sealing, environment, quantity and agreed test method.请提供两端对接界面、标准或反极性、阻抗、频段、功率与直流偏置、最大插入损耗和回波损耗/VSWR 目标、线长与相位要求、屏蔽或 PIM 要求、走线与弯曲半径、面板密封、环境、数量及约定测试方法。 |
| Sample and manufacturing configuration样品与制造配置 | Engineering first freezes the channel definition and mechanical envelope, then builds controlled samples. Released production can include connector gauging, visual and dimensional inspection, continuity and the RF measurements explicitly agreed for the project; limits and fixtures are recorded with the result.工程团队先冻结通道定义与机械包络，再制作受控样品。放行生产可包括连接器量规、外观与尺寸、导通，以及项目明确约定的 RF 测量；限值与夹具与结果一同记录。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Antennas and wireless devices天线与无线设备
Select coax for frequency, connector polarity and installation distance. Define the transmission basis from coax type, impedance and frequency.频段、接头极性及实际安装距离决定同轴选择。选配时，同轴型号、阻抗与频率共同确定传输基础。
RF instrument links射频仪器互连
Specify bands, loss and calibration boundaries for validation. Check series, gender and reverse polarity at the center contacts.测量频段、损耗与校准边界需写入验证要求。选配时，系列、公母及反极性按中心接点核对。
Internal equipment RF paths设备内部射频路径
Check bends, shield transitions and connector support in tight routes. Specify measurement bands and methods for loss and length.紧凑布线时核对弯曲、屏蔽过渡和接头支撑。选配时，插损、回损与长度写明测量频段和方法。
Equipment antenna panels设备天线面板
Define panel thickness, feedthrough and grounding with the RF path. Match stripping, crimping, ends and bend limits to the cable.面板厚度、穿壳接口及接地与射频路径一起定义。选配时，剥线、压接、端头与弯曲配合具体电缆。
Instrument ports and measurement connections仪器端口与测量连接
Define measurement leads from instrument ports, impedance, target frequency range and calibration method. Test-equipment capability does not establish the cable rating. Define the transmission basis from coax type, impedance and frequency.测量引线按仪器端口、阻抗体系、目标频段和校准方式确定；测试设备的能力不能直接当作电缆额定。选配时，同轴型号、阻抗与频率共同确定传输基础。
Internal coaxial construction and routing内部同轴结构与引出
For internal RF connections, review the center conductor, dielectric, shield termination and outlet fixing together so installation bends do not damage the layer construction. Check series, gender and reverse polarity at the center contacts.设备内部的射频连接需同时检查中心导体、介质、屏蔽端接和出口固定，避免安装弯曲损伤层结构。选配时，系列、公母及反极性按中心接点核对。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports rf & coaxial assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕RF与同轴电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Coaxial cable type, impedance and frequency range同轴电缆型号、阻抗与频率范围
Define the transmission basis from coax type, impedance and frequency.同轴型号、阻抗与频率共同确定传输基础。
End connector series, gender and reverse polarity两端连接器系列、性别与反极性
Check series, gender and reverse polarity at the center contacts.系列、公母及反极性按中心接点核对。
Crimp tools, strip dimensions and bend radius压接工具、剥线尺寸与弯曲半径
Match stripping, crimping, ends and bend limits to the cable.剥线、压接、端头与弯曲配合具体电缆。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can an RF cable be selected from connector photos?可以只凭连接器照片选择 RF 电缆吗？
No. Photos help identify a family, but exact interface, gender, polarity, impedance, frequency, cable type, length and environment still require drawings, part numbers or equipment data.不可以。照片只有助于识别系列，精确界面、性别、极性、阻抗、频率、线缆类型、长度与环境仍需图纸、型号或设备资料。
What is the difference between 50-ohm and 75-ohm coax?50Ω 与 75Ω 同轴线有什么区别？
They use different conductor and dielectric geometry and serve different systems. Fifty ohms is common in RF and test equipment; 75 ohms is common in video and broadcast. The cable and both interfaces must match the equipment impedance.它们使用不同导体与介质几何，服务于不同系统。50Ω 常见于 RF 与测试设备，75Ω 常见于视频与广播；线缆和两端界面都必须匹配设备阻抗。
Does a higher-frequency connector guarantee the complete cable rating?使用更高频率连接器就能保证整条电缆频率吗？
No. The usable assembly band is limited by the cable, both connectors, termination quality, transitions, length, routing and acceptance limits. The complete assembly must be reviewed and, where required, measured.不能。组件可用频段受线缆、两端连接器、端接质量、过渡、长度、路由与接收限值共同限制，需要审核完整组件，必要时进行测量。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the fakra to miniature coaxial terminal pigtail assembly. We can use them to review configuration and sample requirements.提供FAKRA转微型同轴端子尾线组件的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。