Ring-terminal end环形端子端头
A ring-terminal end provides a mounting-hole connection. Lead direction, support and insulation coverage can follow the stud position.末端采用带安装孔的环形端子形式，可围绕螺柱位置安排接线方向、端头支撑与绝缘覆盖。
Flame-Retardant Cable阻燃电线电缆
Power Connector to Ring-Terminal Braided Harness电源接头转环形端子编织线束
Power Connector to Ring-Terminal Braided Harness combines ring-terminal end, end transition layout, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.电源接头转环形端子编织线束的结构重点包括环形端子端头、端头转接与组合、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Ring-terminal end环形端子端头
- End transition layout端头转接与组合
- Plug-in connection end插接式端头
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the power connector to ring-terminal braided harness form as a starting point and confirm these design points against drawings and the actual equipment.以电源接头转环形端子编织线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Braided outer protection编织外层
A braid can organize the bundle and protect its surface. Define its material, coverage and end treatment around the routing path; distinguish insulating braid from metallic shielding.编织层可用于束线与表面防磨；材料、覆盖长度和端部收口需结合安装路径确定。绝缘编织与金属屏蔽编织应分别定义。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Specified flame standard, method and class指定阻燃标准、试验方法与等级 | Specify the flame standard, test method and required classification.指定阻燃标准、试验方法及要求等级。 |
|---|---|
| Single-cable or bunched-test scope单根或成束试验适用范围 | Define single-cable or bunched testing to avoid mixing their scopes.明确单根或成束试验，避免混用适用范围。 |
| Jacket/insulation materials and specimen specification护套绝缘材料与试样规格 | Match insulation, jacket and test specimen to the supplied construction.绝缘、护套与试样规格对应实际供货结构。 |
| Test report, model and batch mapping检测报告、型号和批次对应 | Reports must map to the exact model, construction and supply batch.报告需可对应准确型号、结构和供应批次。 |
| Installation and operating boundary安装与使用边界 | Provide exact fire-test method, installation, construction, marking and evidence.请提供准确燃烧试验方法、安装、结构、印字与证据。 |
| Sample and release basis样品与放行依据 | Release records the exact cable identity and supporting fire-test evidence.放行记录包含准确线缆身份与支持燃烧试验证据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Specify the flame standard, test method and required classification.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，指定阻燃标准、试验方法及要求等级。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Define single-cable or bunched testing to avoid mixing their scopes.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，明确单根或成束试验，避免混用适用范围。
Routing and retention in confined spaces狭小空间的布线与固定
Define bends, retention points and assembly order in confined spaces. Do not compensate for an incorrect interface direction or length with forced folds. Match insulation, jacket and test specimen to the supplied construction.狭小空间布线需明确转弯、固定点和拆装顺序，不能用强行折线弥补接口方向或长度误差。选配时，绝缘、护套与试样规格对应实际供货结构。
Equipment power-distribution branches设备电源分配支路
Select power branches from actual loads, circuit protection and route length. Include termination, retention and service positions in the wiring definition. Reports must map to the exact model, construction and supply batch.供电分支以实际负载、回路保护和线长为选配依据，端头、固定和检修位置也需列入布线定义。选配时，报告需可对应准确型号、结构和供应批次。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Specify the flame standard, test method and required classification.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，指定阻燃标准、试验方法及要求等级。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Define single-cable or bunched testing to avoid mixing their scopes.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，明确单根或成束试验，避免混用适用范围。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports flame-retardant cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕阻燃电线电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Specify the flame standard, test method and required classification. Flame retardance is not fire-resistant circuit integrity.指定阻燃标准、试验方法及要求等级。 阻燃不等于耐火保持通电。
Match the actual installation duty匹配实际敷设工况
Define single-cable or bunched testing to avoid mixing their scopes. Flame retardance is not halogen-free or low-smoke performance.明确单根或成束试验，避免混用适用范围。 阻燃不等于无卤或低烟。
Confirm material and inspection documents确认材料与检验文件
Match insulation, jacket and test specimen to the supplied construction. Do not equate classifications from different test systems.绝缘、护套与试样规格对应实际供货结构。 不同试验体系等级不得直接等同。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does flame retardance mean the circuit stays operational in fire?阻燃是否意味着火灾中保持通电？
Flame retardance is not fire-resistant circuit integrity. Specify the flame standard, test method and required classification.阻燃不等于耐火保持通电。指定阻燃标准、试验方法及要求等级。
Does flame retardance also mean halogen-free and low-smoke?阻燃是否同时代表无卤和低烟？
Flame retardance is not halogen-free or low-smoke performance. Define single-cable or bunched testing to avoid mixing their scopes.阻燃不等于无卤或低烟。明确单根或成束试验，避免混用适用范围。
Can classifications from different flame-test systems be treated as equivalent?不同阻燃体系的等级能直接等同吗？
Do not equate classifications from different test systems. Match insulation, jacket and test specimen to the supplied construction.不同试验体系等级不得直接等同。绝缘、护套与试样规格对应实际供货结构。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the power connector to ring-terminal braided harness. We can use them to review configuration and sample requirements.提供电源接头转环形端子编织线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。