Interface and function review接口与功能确认
AWM recognition does not establish appliance approvalAWM认可不等于电器整机批准
Appliance Wire & Cable电器电线电缆
Refrigerator Power Plug Harness冰箱电源插头线束
Refrigerator Power Plug Harness can be configured around equipment interfaces and routing. Appliance wire and cable connect power, controls, motors, heaters and sensors across different thermal, moisture, movement and service zones inside equipment.冰箱电源插头线束可围绕设备接口与安装路径进行配置。电器电线电缆连接设备内部的电源、控制器、电机、加热器与传感器，并跨越不同温度、潮气、运动与维修区域。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the refrigerator power plug harness form as a starting point and confirm these design points against drawings and the actual equipment.以冰箱电源插头线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Installation and acceptance安装与验收
The same style may have different gauges and diameters相同式样可能有不同线径和外径
Manufacturing reference制造依据
Confirm drawings, circuit mapping, dimensional datums and sample revision before manufacture to control fit checks and repeat production.确认图纸、连接关系、尺寸基准和样品版本后再制作，减少试装与重复生产中的差异。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| AWM/other wire style, standard and documentsAWM或其他线材式样、标准与文件 | Check current documents for the specified AWM style or other wire standard.按指定AWM式样或其他线材标准核对有效文件。 |
|---|---|
| Conductor specification, stranding and plating导体规格、绞合和镀层 | Match conductor gauge, stranding and plating to the termination process.导体线规、绞合和镀层须匹配端接工艺。 |
| Rated voltage/temperature and insulation construction额定电压、温度与绝缘结构 | Tie voltage, temperature and insulation construction to the exact wire model.电压、温度与绝缘层结构对应准确线材型号。 |
| Flame test, marking and traceability阻燃试验、印字与追溯 | Include flame-test method, marking and traceability in material acceptance.阻燃方法、印字和追溯信息列入材料验收要求。 |
| Installation and operating boundary安装与使用边界 | Provide the destination market, appliance zone map, circuit loads, temperatures, exposure, movement, wire or cord designation, terminal system and validation plan.请提供目标市场、电器分区图、回路负载、温度、环境暴露、运动状态、线材或软线型号、端子系统与验证方案。 |
| Sample and release basis样品与放行依据 | Release records the exact wire or cord, conductor and insulation construction, marking, termination, routing, protection, traceability and agreed assembly checks.放行文件记录准确线材或软线、导体与绝缘结构、印字、端接、布线、防护、追溯及约定组件检查。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Equipment power-distribution branches设备电源分配支路
Select power branches from actual loads, circuit protection and route length. Include termination, retention and service positions in the wiring definition. Check current documents for the specified AWM style or other wire standard.供电分支以实际负载、回路保护和线长为选配依据，端头、固定和检修位置也需列入布线定义。选配时，按指定AWM式样或其他线材标准核对有效文件。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Match conductor gauge, stranding and plating to the termination process.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，导体线规、绞合和镀层须匹配端接工艺。
Conductor construction and termination fit导体结构与端接适配
Match conductor area and stranding to load and terminal limits. Insulation diameter also affects tooling, seals and cable retention. Tie voltage, temperature and insulation construction to the exact wire model.导体截面与股线结构需要对应实际负载和端子范围，绝缘外径还会影响工具、密封与夹持选择。选配时，电压、温度与绝缘层结构对应准确线材型号。
Relays and auxiliary power ends继电器与辅助供电端
Separate coil and load circuits at relay leads. Define terminals, conductor size and protection devices together from the schematic. Include flame-test method, marking and traceability in material acceptance.继电器引线需要区分线圈与负载回路，端子定义、线径和保护元件由原理图共同确定。选配时，阻燃方法、印字和追溯信息列入材料验收要求。
Routing boundaries around hot equipment热区设备的布线边界
Separate continuous temperature, peaks and exposure time around hot equipment. Review wire, terminals and protective parts against their own limits. Check current documents for the specified AWM style or other wire standard.热区布线需要区分连续温度、峰值和暴露时间，线材、端子及保护件应按各自限制评审。选配时，按指定AWM式样或其他线材标准核对有效文件。
Display-module and control-board connections显示模块与控制板连接
Check insertion direction, contact orientation and frame clearance at display modules. Mark fixed folds on the assembly drawing. Match conductor gauge, stranding and plating to the termination process.显示模块连接需核对插入方向、触点朝向与边框空间，并将固定折弯的位置标入装配图。选配时，导体线规、绞合和镀层须匹配端接工艺。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports appliance wire & cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕电器电线电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Check current documents for the specified AWM style or other wire standard. AWM recognition does not establish appliance approval.按指定AWM式样或其他线材标准核对有效文件。 AWM认可不等于电器整机批准。
Match the actual installation duty匹配实际敷设工况
Match conductor gauge, stranding and plating to the termination process. The same style may have different gauges and diameters.导体线规、绞合和镀层须匹配端接工艺。 相同式样可能有不同线径和外径。
Confirm material and inspection documents确认材料与检验文件
Tie voltage, temperature and insulation construction to the exact wire model. Page models are source clues, not supply commitments.电压、温度与绝缘层结构对应准确线材型号。 页面型号仅为来源线索不是供货承诺。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does AWM recognition establish appliance approval?AWM认可是否代表电器整机批准？
AWM recognition does not establish appliance approval. Check current documents for the specified AWM style or other wire standard.AWM认可不等于电器整机批准。按指定AWM式样或其他线材标准核对有效文件。
Do all wires of one style have the same dimensions?相同式样的线材尺寸都一样吗？
The same style may have different gauges and diameters. Match conductor gauge, stranding and plating to the termination process.相同式样可能有不同线径和外径。导体线规、绞合和镀层须匹配端接工艺。
Does an example model constitute a fixed supply commitment?示例型号是否等于固定供货承诺？
Page models are source clues, not supply commitments. Tie voltage, temperature and insulation construction to the exact wire model.页面型号仅为来源线索不是供货承诺。电压、温度与绝缘层结构对应准确线材型号。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the refrigerator power plug harness. We can use them to review configuration and sample requirements.提供冰箱电源插头线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。