Angled cable exit弯式出线方向
The end transitions into an angled cable exit, allowing routing to turn beside the interface. Align its direction with the enclosure and neighboring ports.端头与线缆采用弯式过渡，便于在接口旁转向布线。弯头朝向应与机壳和邻近接口空间配合。
RF & Coaxial AssemblyRF与同轴电缆组件
Right-Angle BNC to Right-Angle SMA Coaxial Cable直角BNC转直角SMA同轴线
Right-Angle BNC to Right-Angle SMA Coaxial Cable combines angled cable exit, bnc-form end, compact coaxial interface end. Interface, circuit and installation data guide dimensions, material selection and sample review.直角BNC转直角SMA同轴线的结构重点包括弯式出线方向、BNC形式端头、小型同轴接口端。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Angled cable exit弯式出线方向
- BNC-form endBNC形式端头
- Compact coaxial interface end小型同轴接口端
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the right-angle bnc to right-angle sma coaxial cable form as a starting point and confirm these design points against drawings and the actual equipment.以直角BNC转直角SMA同轴线的结构形式为起点，结合图纸和实际设备确认以下设计要点。
BNC-form endBNC形式端头
The BNC-form end can be arranged around the equipment panel and cable route, with clearance for mating.BNC形式的连接端可配合设备面板和线缆走向布置，插接操作空间需保留。
Compact coaxial interface end小型同轴接口端
The compact coaxial-form end fits a compact interface layout. Arrange bends and end support to avoid pulling directly on contacts.小型同轴形式的端头可用于紧凑接口布局，线缆转弯与端头支撑需避免直接牵拉接点。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Signal path信号路径
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Coaxial cable type, impedance and frequency range同轴电缆型号、阻抗与频率范围 | Define the transmission basis from coax type, impedance and frequency.同轴型号、阻抗与频率共同确定传输基础。 |
|---|---|
| End connector series, gender and reverse polarity两端连接器系列、性别与反极性 | Check series, gender and reverse polarity at the center contacts.系列、公母及反极性按中心接点核对。 |
| Length, insertion-loss and return-loss conditions长度、插损与回损验收条件 | Specify measurement bands and methods for loss and length.插损、回损与长度写明测量频段和方法。 |
| Crimp tools, strip dimensions and bend radius压接工具、剥线尺寸与弯曲半径 | Match stripping, crimping, ends and bend limits to the cable.剥线、压接、端头与弯曲配合具体电缆。 |
| Circuit and revision reference电路与版本依据 | Provide both mating interfaces, standard or reverse polarity, impedance, frequency band, power and DC bias, maximum insertion loss and return-loss/VSWR target, cable length and phase requirement, shielding or PIM requirement, routing and bend radius, panel sealing, environment, quantity and agreed test method.请提供两端对接界面、标准或反极性、阻抗、频段、功率与直流偏置、最大插入损耗和回波损耗/VSWR 目标、线长与相位要求、屏蔽或 PIM 要求、走线与弯曲半径、面板密封、环境、数量及约定测试方法。 |
| Sample and manufacturing configuration样品与制造配置 | Engineering first freezes the channel definition and mechanical envelope, then builds controlled samples. Released production can include connector gauging, visual and dimensional inspection, continuity and the RF measurements explicitly agreed for the project; limits and fixtures are recorded with the result.工程团队先冻结通道定义与机械包络，再制作受控样品。放行生产可包括连接器量规、外观与尺寸、导通，以及项目明确约定的 RF 测量；限值与夹具与结果一同记录。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Antennas and wireless devices天线与无线设备
Select coax for frequency, connector polarity and installation distance. Define the transmission basis from coax type, impedance and frequency.频段、接头极性及实际安装距离决定同轴选择。选配时，同轴型号、阻抗与频率共同确定传输基础。
RF instrument links射频仪器互连
Specify bands, loss and calibration boundaries for validation. Check series, gender and reverse polarity at the center contacts.测量频段、损耗与校准边界需写入验证要求。选配时，系列、公母及反极性按中心接点核对。
Internal equipment RF paths设备内部射频路径
Check bends, shield transitions and connector support in tight routes. Specify measurement bands and methods for loss and length.紧凑布线时核对弯曲、屏蔽过渡和接头支撑。选配时，插损、回损与长度写明测量频段和方法。
Equipment antenna panels设备天线面板
Define panel thickness, feedthrough and grounding with the RF path. Match stripping, crimping, ends and bend limits to the cable.面板厚度、穿壳接口及接地与射频路径一起定义。选配时，剥线、压接、端头与弯曲配合具体电缆。
Instrument ports and measurement connections仪器端口与测量连接
Define measurement leads from instrument ports, impedance, target frequency range and calibration method. Test-equipment capability does not establish the cable rating. Define the transmission basis from coax type, impedance and frequency.测量引线按仪器端口、阻抗体系、目标频段和校准方式确定；测试设备的能力不能直接当作电缆额定。选配时，同轴型号、阻抗与频率共同确定传输基础。
Internal coaxial construction and routing内部同轴结构与引出
For internal RF connections, review the center conductor, dielectric, shield termination and outlet fixing together so installation bends do not damage the layer construction. Check series, gender and reverse polarity at the center contacts.设备内部的射频连接需同时检查中心导体、介质、屏蔽端接和出口固定，避免安装弯曲损伤层结构。选配时，系列、公母及反极性按中心接点核对。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports rf & coaxial assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕RF与同轴电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Coaxial cable type, impedance and frequency range同轴电缆型号、阻抗与频率范围
Define the transmission basis from coax type, impedance and frequency.同轴型号、阻抗与频率共同确定传输基础。
End connector series, gender and reverse polarity两端连接器系列、性别与反极性
Check series, gender and reverse polarity at the center contacts.系列、公母及反极性按中心接点核对。
Crimp tools, strip dimensions and bend radius压接工具、剥线尺寸与弯曲半径
Match stripping, crimping, ends and bend limits to the cable.剥线、压接、端头与弯曲配合具体电缆。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can an RF cable be selected from connector photos?可以只凭连接器照片选择 RF 电缆吗？
No. Photos help identify a family, but exact interface, gender, polarity, impedance, frequency, cable type, length and environment still require drawings, part numbers or equipment data.不可以。照片只有助于识别系列，精确界面、性别、极性、阻抗、频率、线缆类型、长度与环境仍需图纸、型号或设备资料。
What is the difference between 50-ohm and 75-ohm coax?50Ω 与 75Ω 同轴线有什么区别？
They use different conductor and dielectric geometry and serve different systems. Fifty ohms is common in RF and test equipment; 75 ohms is common in video and broadcast. The cable and both interfaces must match the equipment impedance.它们使用不同导体与介质几何，服务于不同系统。50Ω 常见于 RF 与测试设备，75Ω 常见于视频与广播；线缆和两端界面都必须匹配设备阻抗。
Does a higher-frequency connector guarantee the complete cable rating?使用更高频率连接器就能保证整条电缆频率吗？
No. The usable assembly band is limited by the cable, both connectors, termination quality, transitions, length, routing and acceptance limits. The complete assembly must be reviewed and, where required, measured.不能。组件可用频段受线缆、两端连接器、端接质量、过渡、长度、路由与接收限值共同限制，需要审核完整组件，必要时进行测量。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the right-angle bnc to right-angle sma coaxial cable. We can use them to review configuration and sample requirements.提供直角BNC转直角SMA同轴线的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。