Branched end layout分支端头布局
Conductors separate toward different ends, creating individual connection points. Branch lengths and directions can follow the equipment modules.导线向不同端头分出，形成独立接入位置。各支路可围绕设备模块分别安排长度与方向。
TE / AMP CompatibleTE / AMP兼容组件
Seat Rectangular Connector Corrugated-Conduit Branch Harness座椅矩形接头波纹护管分支线束
Seat Rectangular Connector Corrugated-Conduit Branch Harness combines branched end layout, rectangular interface form, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.座椅矩形接头波纹护管分支线束的结构重点包括分支端头布局、矩形接口外形、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Branched end layout分支端头布局
- Rectangular interface form矩形接口外形
- Plug-in connection end插接式端头
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the seat rectangular connector corrugated-conduit branch harness form as a starting point and confirm these design points against drawings and the actual equipment.以座椅矩形接头波纹护管分支线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Rectangular interface form矩形接口外形
The rectangular interface form allows end position and service clearance to follow the mating face, latch and cable exit.接口采用矩形轮廓，可围绕插入面、卡扣与线束出口安排端头位置和拆装空间。
Corrugated covering form波纹管形态防护
The external covering has a corrugated form, with openings and fixing arranged around route bends and breakouts.外部覆盖采用波纹管形态，可围绕走线弯曲和分支位置安排端口与固定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Full TE/AMP housing, terminal and seal part numbersTE/AMP完整壳体、端子与密封件料号 | Record full part numbers for housings, contacts, seals and secondary locks.同时记录壳体、端子、线封与二次锁的完整料号。 |
|---|---|
| Series, pitch, keying and mating part系列、间距、键位与对插件 | Check mating drawings, keying and orientation for the exact series.按具体系列核对对插图、键位和接口方向。 |
| Terminal wire range, plating and tooling requirements端子适配线径、镀层与工具要求 | Use contact application documents to define conductor range, insulation support and crimp tooling.用端子应用文件确定导体范围、绝缘支撑与压接工装。 |
| Original/alternative source and permitted scope原厂或替代来源及准许范围 | List specified components and proposed alternatives separately in the approved BOM.指定物料与拟议替代分别列入认可清单。 |
| Installation and operating boundary安装与使用边界 | Send full part numbers, mating drawings, cavity assignment, wire size and insulation diameter, environment, quantity and inspection requirements.请提供完整料号、对插图纸、腔位定义、线径与绝缘外径、使用环境、数量及检验要求。 |
| Sample and release basis样品与放行依据 | Review parts and tooling, approve first articles, then produce against controlled drawings and the agreed inspection plan.审核物料与工装，完成首件认可后，按受控图纸和约定检验计划生产。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Interfaces within engine-bay layouts发动机舱内的接口布置
Map heat sources, fluid exposure and service routes together. Allow assembly space around connector ends and cable supports. Record full part numbers for housings, contacts, seals and secondary locks.发动机舱连接要把热源、油液暴露和检修路径放在同一张布线图中，端头与固定点也需留出装配空间。选配时，同时记录壳体、端子、线封与二次锁的完整料号。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Check mating drawings, keying and orientation for the exact series.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，按具体系列核对对插图、键位和接口方向。
Equipment panels and circular interfaces设备面板与圆形接口
Start with the cutout, panel thickness, mounting direction and rear clearance. Coordinate contact arrangement and cable exit with the complete assembly view. Use contact application documents to define conductor range, insulation support and crimp tooling.面板连接以开孔、板厚、装配方向和后方净空为起点；接点排列与电缆出口还需要对应完整总装视图。选配时，用端子应用文件确定导体范围、绝缘支撑与压接工装。
Relays and auxiliary power ends继电器与辅助供电端
Separate coil and load circuits at relay leads. Define terminals, conductor size and protection devices together from the schematic. List specified components and proposed alternatives separately in the approved BOM.继电器引线需要区分线圈与负载回路，端子定义、线径和保护元件由原理图共同确定。选配时，指定物料与拟议替代分别列入认可清单。
Enclosure entries and cable retention机箱穿线与入口固定
Match cable entries to actual diameter, panel thickness and fixing method. Keep jacket retention independent of the internal termination. Record full part numbers for housings, contacts, seals and secondary locks.线缆入口需匹配实际外径、板厚和固定方式；护套夹持与内部端接之间应保留独立的支撑路径。选配时，同时记录壳体、端子、线封与二次锁的完整料号。
Vehicle service connections车辆检修转接位置
Provide access for mating and service tools. Record end-face views and cable retention after service; appearance alone does not establish interchangeability. Check mating drawings, keying and orientation for the exact series.可拆卸尾线应保留插拔与工具空间，并记录端视图和维修后的固定方式，避免只凭外观确定替换关系。选配时，按具体系列核对对插图、键位和接口方向。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports te / amp compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕TE / AMP兼容组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Record full part numbers for housings, contacts, seals and secondary locks. The AMP family name does not identify a mating system.同时记录壳体、端子、线封与二次锁的完整料号。 AMP家族名称不能确定具体插合系统。
Define cable and installation conditions定义线材与安装条件
Check mating drawings, keying and orientation for the exact series. Equal cavity count does not establish terminal/seal fit.按具体系列核对对插图、键位和接口方向。 相同孔数不证明端子与密封件匹配。
Set processing and acceptance requirements确定加工与验收要求
Use contact application documents to define conductor range, insulation support and crimp tooling. Original source or authorization requires document verification.用端子应用文件确定导体范围、绝缘支撑与压接工装。 原厂来源或授权需文件验证。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does the AMP name identify the mating connector?AMP名称能直接确定对插件吗？
The AMP family name does not identify a mating system. Record full part numbers for housings, contacts, seals and secondary locks.AMP家族名称不能确定具体插合系统。同时记录壳体、端子、线封与二次锁的完整料号。
Do equal cavity counts mean the contacts are interchangeable?孔数一样就能使用同一组端子吗？
Equal cavity count does not establish terminal/seal fit. Check mating drawings, keying and orientation for the exact series.相同孔数不证明端子与密封件匹配。按具体系列核对对插图、键位和接口方向。
How is the supply scope for original or alternative parts defined?如何确定原厂件或替代件的供货范围？
Original source or authorization requires document verification. Use contact application documents to define conductor range, insulation support and crimp tooling.原厂来源或授权需文件验证。用端子应用文件确定导体范围、绝缘支撑与压接工装。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the seat rectangular connector corrugated-conduit branch harness. We can use them to review configuration and sample requirements.提供座椅矩形接头波纹护管分支线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。