D-Sub interface endD-Sub接口端
The D-Sub-form end allows equipment connection to be arranged around the mating face, fixing screws and rear cable route.端头采用D-Sub形式，可围绕插合面、固定螺钉和后部线缆走向安排设备连接。
Hybrid Power/Data Cable Assembly复合动力与数据电缆组件
Servo D-sub to Rectangular Power Connector Harness伺服D-sub转矩形电源接头线束
Servo D-sub to Rectangular Power Connector Harness combines d-sub interface end, rectangular interface form, end transition layout. Interface, circuit and installation data guide dimensions, material selection and sample review.伺服D-sub转矩形电源接头线束的结构重点包括D-Sub接口端、矩形接口外形、端头转接与组合。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- D-Sub interface endD-Sub接口端
- Rectangular interface form矩形接口外形
- End transition layout端头转接与组合
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the servo d-sub to rectangular power connector harness form as a starting point and confirm these design points against drawings and the actual equipment.以伺服D-sub转矩形电源接头线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Rectangular interface form矩形接口外形
The rectangular interface form allows end position and service clearance to follow the mating face, latch and cable exit.接口采用矩形轮廓，可围绕插入面、卡扣与线束出口安排端头位置和拆装空间。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Power and data channel allocation动力与数据通道分配 | Allocate channels by power, data and auxiliary functions.按动力、数据和辅助功能划分通道。 |
|---|---|
| Hybrid contact ratings and insulation spacing混合接点额定与绝缘间隔 | Review hybrid contacts and spacing for current and voltage.混合接点与绝缘间隔结合电流和电压评估。 |
| Signal impedance, shielding and grounding layout信号阻抗、屏蔽与接地布局 | Use shields, differential pairs and grounding to address coupling.屏蔽、差分线对及接地路径控制耦合干扰。 |
| Common-jacket diameter, motion and thermal conditions共同护套外径、运动及温升条件 | Define installation from overall diameter, common jacket and motion.外径、共护套和运动条件一起确定安装结构。 |
| Circuit and revision reference电路与版本依据 | Provide the power and data circuit diagrams, pin maps, exact hybrid-cable reference, mating connectors, breakout lengths, route and motion profile, and project-specific acceptance limits.请提供供电与数据回路图、针脚表、准确的复合电缆型号、对插件、分支长度、布线路径与运动工况，以及项目特定验收限值。 |
| Sample and manufacturing configuration样品与制造配置 | We review the cable source and assembly feasibility for the project, then define sample dimensions, termination, strain relief and separate electrical and data-path checks before release.按项目审核线材来源与组装可行性，再定义样品尺寸、端接、应力释放及供电和数据通道各自的检验项目后放行。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Drive and power-module connections驱动与电源模块连接
Define supply, feedback and control circuits separately for a drive project. Confirm ports, wire sizes and shielding before combining them into a hybrid assembly. Allocate channels by power, data and auxiliary functions.驱动项目需分别定义电源、反馈及控制回路，明确各端口、线规和屏蔽要求后再组成复合组件。选配时，按动力、数据和辅助功能划分通道。
Hybrid equipment interfaces复合设备接口
Allocate contacts and jackets by channel within limited interface space. Review hybrid contacts and spacing for current and voltage.在有限接口空间中按通道配置接点与护套。选配时，混合接点与绝缘间隔结合电流和电压评估。
Automation module links自动化模块连接
Define power, communication and mounting boundaries for removable modules. Use shields, differential pairs and grounding to address coupling.可拆模块的供电、通信和安装边界一起定义。选配时，屏蔽、差分线对及接地路径控制耦合干扰。
Panel cable entries and branch outlets面板穿线与分支出口
At a panel, check cable entries, glands, branch positions and access to the ends. Record the electrical definition in a separate pin table. Define installation from overall diameter, common jacket and motion.面板处需检查穿线口、固定接头、分支位置和端头操作空间；组件的电气定义另列针脚表。选配时，外径、共护套和运动条件一起确定安装结构。
Moving module connections移动模块连接
Match the shared-jacket construction to bends, torsion and fixing. Allocate channels by power, data and auxiliary functions.共护套结构需对应弯曲、扭转和固定条件。选配时，按动力、数据和辅助功能划分通道。
Test and development adapters测试与开发转接
Define measurement access and acceptance boundaries separately for power/data. Review hybrid contacts and spacing for current and voltage.为动力与数据分别定义测量接入和验收边界。选配时，混合接点与绝缘间隔结合电流和电压评估。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports hybrid power/data cable assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕复合动力与数据电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Power and data channel allocation动力与数据通道分配
Allocate channels by power, data and auxiliary functions.按动力、数据和辅助功能划分通道。
Hybrid contact ratings and insulation spacing混合接点额定与绝缘间隔
Review hybrid contacts and spacing for current and voltage.混合接点与绝缘间隔结合电流和电压评估。
Common-jacket diameter, motion and thermal conditions共同护套外径、运动及温升条件
Define installation from overall diameter, common jacket and motion.外径、共护套和运动条件一起确定安装结构。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Why review power and data together?动力与数据为什么需要一起审核？
Assess coupled noise under the actual power load动力耦合噪声需按实际负载验证
Does a shared jacket establish adequate circuit isolation?共护套是否就代表回路隔离充分？
A shared jacket does not establish adequate circuit isolation同护套多功能不证明彼此隔离足够
Does connector capability define the whole assembly?单个接头能力能代表整条组件吗？
A chip or connector capability does not define full-assembly capability单芯片或接头能力不是整条组件能力
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the servo d-sub to rectangular power connector harness. We can use them to review configuration and sample requirements.提供伺服D-sub转矩形电源接头线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。