Interface and function review接口与功能确认
Record vehicle service numbers separately from connector numbers车厂服务号与连接器件号分别记录
Yazaki Interface Harness ProjectYazaki接口线束项目
VXM-145 Series Vehicle Display Adapter HarnessVXM-145系列接口 · 车载显示器转接线束
VXM-145 Series Vehicle Display Adapter Harness can be configured around equipment interfaces and routing. Sensor leads, vehicle branches, equipment adapters and removable harnesses built around customer-specified Yazaki connectors. We verify the exact housing, terminal, wire seal, secondary lock and mating half before defining pins, cable and routing; a family name is not a complete configuration.VXM-145系列接口 · 车载显示器转接线束可围绕设备接口与安装路径进行配置。围绕客户指定的矢崎 Yazaki 连接器，制作传感器引线、车身分支、设备转接与可拆卸线束。先核对准确壳体、端子、线封、二次锁及对插件，再决定针脚、线材和安装走向；系列名称本身不能代替完整配置。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the vxm-145 series vehicle display adapter harness form as a starting point and confirm these design points against drawings and the actual equipment.以VXM-145系列接口 · 车载显示器转接线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Installation and acceptance安装与验收
Include secondary-lock assembly status in inspection二次锁装配状态要有检查点
Manufacturing reference制造依据
Confirm drawings, circuit mapping, dimensional datums and sample revision before manufacture to control fit checks and repeat production.确认图纸、连接关系、尺寸基准和样品版本后再制作，减少试装与重复生产中的差异。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Full Yazaki series, housing and terminal part numbersYazaki系列、壳体与端子完整料号 | Retain complete Yazaki family, housing and contact part-number suffixes.保留Yazaki系列、壳体和端子件号的完整后缀。 |
|---|---|
| Vehicle mating part, pin layout and keying车辆对插件、针位与键位 | Confirm keying, cavity drawings and orientation against the vehicle mate.按车辆对插件确认键位、针位图和接口方向。 |
| Wire seals, secondary locks and wire range线封、二次锁和适用线径 | Match seals and secondary locks to the actual conductor and insulation diameter.线封、二次锁与实际导体及绝缘外径配套。 |
| Contact retention, sealing and temperature evidence端子保持、密封及温度依据 | Define retention, sealing and temperature acceptance for the actual configuration.保持、密封和温度要求按实际配置确定验收依据。 |
| Installation and operating boundary安装与使用边界 | For quotation, provide housing and mating part numbers, mating-face pin views, terminals and seals, circuit map, conductors, environment and temperature, fixing points, branch dimensions, quantity and acceptance criteria. Photos or an old sample aid identification but do not authorize unseen electrical functions or substitute parts.询价请提供两侧壳体与对插件料号、正视针脚图、端子和线封、回路表、导体规格、环境与温度、固定点、分支尺寸、数量和验收要求。照片和旧样可辅助识别，却不能证明不可见的电气功能或替代料获准。 |
| Sample and release basis样品与放行依据 | Approved inputs become a controlled BOM, pin map, assembly instructions and first-article checkpoints. Check crimps, terminal retention, seal position, secondary lock, branch dimensions, continuity and mating. Ingress, vibration, dielectric or vehicle-level suitability requires exact component data and separately agreed project validation.批准后的配置转化为受控 BOM、针脚表、加工与首件检查点。核查压接、端子保持、线封位置、二次锁、支路尺寸、导通与对插；防水、耐振、耐压或整车适配须以指定零件资料和项目试验单独确认。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Interfaces within engine-bay layouts发动机舱内的接口布置
Map heat sources, fluid exposure and service routes together. Allow assembly space around connector ends and cable supports. Retain complete Yazaki family, housing and contact part-number suffixes.发动机舱连接要把热源、油液暴露和检修路径放在同一张布线图中，端头与固定点也需留出装配空间。选配时，保留Yazaki系列、壳体和端子件号的完整后缀。
Vehicle control-module leads车辆控制模块引线
Separate interface cavities, power circuits and signal circuits at controller leads. Set branch dimensions from the module and mounting-point positions. Confirm keying, cavity drawings and orientation against the vehicle mate.控制模块尾线需要清楚区分接口腔位、电源和信号回路；分支尺寸应对应模块与固定点的位置。选配时，按车辆对插件确认键位、针位图和接口方向。
Vehicle service connections车辆检修转接位置
Provide access for mating and service tools. Record end-face views and cable retention after service; appearance alone does not establish interchangeability. Match seals and secondary locks to the actual conductor and insulation diameter.可拆卸尾线应保留插拔与工具空间，并记录端视图和维修后的固定方式，避免只凭外观确定替换关系。选配时，线封、二次锁与实际导体及绝缘外径配套。
Equipment control-board connections设备控制板连接
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Define retention, sealing and temperature acceptance for the actual configuration.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，保持、密封和温度要求按实际配置确定验收依据。
Vehicle lighting and body connections车载灯具与车身连接
Coordinate mating clearance, cable retention and body routing around lighting units. Define circuit functions from the target equipment wiring diagram. Retain complete Yazaki family, housing and contact part-number suffixes.灯具附近的引线需要协调插接空间、线缆固定和车身走线路径，电路功能以目标设备接线图为依据。选配时，保留Yazaki系列、壳体和端子件号的完整后缀。
Chassis and mobile-machine connections底盘与移动机械连接
Keep routing clear of moving parts, abrasion points and water traps. Define connector orientation and nearby retention with the installation route. Confirm keying, cavity drawings and orientation against the vehicle mate.底盘和移动机械的走线需要避开运动件、磨损点与积水位置，接口朝向和近端固定应随安装路径一起定义。选配时，按车辆对插件确认键位、针位图和接口方向。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports yazaki interface harness project projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕Yazaki接口线束项目的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Retain complete Yazaki family, housing and contact part-number suffixes. Record vehicle service numbers separately from connector numbers.保留Yazaki系列、壳体和端子件号的完整后缀。 车厂服务号与连接器件号分别记录。
Define cable and installation conditions定义线材与安装条件
Confirm keying, cavity drawings and orientation against the vehicle mate. Include secondary-lock assembly status in inspection.按车辆对插件确认键位、针位图和接口方向。 二次锁装配状态要有检查点。
Set processing and acceptance requirements确定加工与验收要求
Match seals and secondary locks to the actual conductor and insulation diameter. Vehicle photos do not establish whole-platform compatibility.线封、二次锁与实际导体及绝缘外径配套。 车型照片不能证明全平台兼容。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Is a vehicle service number the same as a connector part number?车厂服务号等同于连接器件号吗？
Record vehicle service numbers separately from connector numbers. Retain complete Yazaki family, housing and contact part-number suffixes.车厂服务号与连接器件号分别记录。保留Yazaki系列、壳体和端子件号的完整后缀。
How is secondary-lock assembly included in inspection?二次锁安装如何纳入检查？
Include secondary-lock assembly status in inspection. Confirm keying, cavity drawings and orientation against the vehicle mate.二次锁装配状态要有检查点。按车辆对插件确认键位、针位图和接口方向。
Does a vehicle photograph establish platform-wide fitment?同车型照片能证明全平台适配吗？
Vehicle photos do not establish whole-platform compatibility. Match seals and secondary locks to the actual conductor and insulation diameter.车型照片不能证明全平台兼容。线封、二次锁与实际导体及绝缘外径配套。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the vxm-145 series vehicle display adapter harness. We can use them to review configuration and sample requirements.提供VXM-145系列接口 · 车载显示器转接线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。