Branched end layout分支端头布局
Conductors separate toward different ends, creating individual connection points. Branch lengths and directions can follow the equipment modules.导线向不同端头分出，形成独立接入位置。各支路可围绕设备模块分别安排长度与方向。
High-Temperature Wire & Cable耐高温电线电缆
White Braided Sleeve Circular Plug Branch Harness白色编织护套圆形插头分支线束
White Braided Sleeve Circular Plug Branch Harness combines branched end layout, circular connection end, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.白色编织护套圆形插头分支线束的结构重点包括分支端头布局、圆形连接端、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Branched end layout分支端头布局
- Circular connection end圆形连接端
- Plug-in connection end插接式端头
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the white braided sleeve circular plug branch harness form as a starting point and confirm these design points against drawings and the actual equipment.以白色编织护套圆形插头分支线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Braided outer form编织形态外层
The outer covering has a braided form. Coverage segments and finishing can follow breakouts, routing passages and fixing positions.外层呈编织形态，可按分支出口、穿线位置和固定点定义覆盖段与收尾。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| High-temperature wire type, insulation and conductor plating高温线材型号、绝缘与导体镀层 | Confirm insulation, conductor plating and documents for the exact model.按准确型号确认绝缘材料、导体镀层及文件。 |
|---|---|
| Continuous, short-term and ambient temperature conditions连续、短时与环境温度条件 | State continuous, short-duration and ambient temperature conditions separately.分别说明持续、短时及周围环境温度条件。 |
| Voltage, heat aging and chemical environment电压、热老化及化学环境 | Review voltage, thermal aging and chemical exposure for the actual project.电压、热老化和化学暴露按实际项目审核。 |
| Terminal, sleeve and full-assembly thermal limits端子、套管与整套组件温度边界 | Define assembly boundaries from the separate limits of contacts, sleeves and wire.以端子、套管与线材中各自限制定义组件边界。 |
| Installation and operating boundary安装与使用边界 | Provide the thermal map, current, route, connector drawings, material data and acceptance criteria.请提供温度分布、电流、路径、接头图纸、材料数据及验收标准。 |
| Sample and release basis样品与放行依据 | Release the complete assembly against approved drawings and project-specific thermal and electrical checks.按获批图纸及项目特定的热工、电气检查放行完整组件。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Routing boundaries around hot equipment热区设备的布线边界
Separate continuous temperature, peaks and exposure time around hot equipment. Review wire, terminals and protective parts against their own limits. Confirm insulation, conductor plating and documents for the exact model.热区布线需要区分连续温度、峰值和暴露时间，线材、端子及保护件应按各自限制评审。选配时，按准确型号确认绝缘材料、导体镀层及文件。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. State continuous, short-duration and ambient temperature conditions separately.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，分别说明持续、短时及周围环境温度条件。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Review voltage, thermal aging and chemical exposure for the actual project.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，电压、热老化和化学暴露按实际项目审核。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Define assembly boundaries from the separate limits of contacts, sleeves and wire.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，以端子、套管与线材中各自限制定义组件边界。
Instrument inputs and measurement leads仪器输入与测量引线
Start measurement leads from signal type, input conditions and grounding. Select pairs and shields for the actual measurement range and noise target. Confirm insulation, conductor plating and documents for the exact model.测量引线以信号类型、输入条件和接地方式为起点，线对与屏蔽选择需要对应实际量程和噪声目标。选配时，按准确型号确认绝缘材料、导体镀层及文件。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. State continuous, short-duration and ambient temperature conditions separately.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，分别说明持续、短时及周围环境温度条件。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports high-temperature wire & cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕耐高温电线电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Confirm insulation, conductor plating and documents for the exact model. Maximum material temperature is not the full-assembly rating.按准确型号确认绝缘材料、导体镀层及文件。 材料最高温度不等于整条组件额定。
Match the actual installation duty匹配实际敷设工况
State continuous, short-duration and ambient temperature conditions separately. High-temperature resistance does not automatically mean flame retardance.分别说明持续、短时及周围环境温度条件。 耐高温不自动意味着阻燃。
Confirm material and inspection documents确认材料与检验文件
Review voltage, thermal aging and chemical exposure for the actual project. Assess heat-source clearance and local hot spots.电压、热老化和化学暴露按实际项目审核。 热源距离和局部热点需实际评估。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Is the material maximum temperature the assembly rating?材料最高温度等于组件额定吗？
Maximum material temperature is not the full-assembly rating. Confirm insulation, conductor plating and documents for the exact model.材料最高温度不等于整条组件额定。按准确型号确认绝缘材料、导体镀层及文件。
Is high-temperature wire necessarily flame-retardant?耐高温线材是否一定阻燃？
High-temperature resistance does not automatically mean flame retardance. State continuous, short-duration and ambient temperature conditions separately.耐高温不自动意味着阻燃。分别说明持续、短时及周围环境温度条件。
Can a nominal temperature replace local hot-spot review?标称温度能代替局部热点评估吗？
Assess heat-source clearance and local hot spots. Review voltage, thermal aging and chemical exposure for the actual project.热源距离和局部热点需实际评估。电压、热老化和化学暴露按实际项目审核。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the white braided sleeve circular plug branch harness. We can use them to review configuration and sample requirements.提供白色编织护套圆形插头分支线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。