Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
PTFE Cable TerminationPTFE电缆端接
6-Pin White-Connector Pigtail六针白色端子开口尾线束
6-Pin White-Connector Pigtail combines plug-in connection end, terminal connection section, pigtail connection form. Interface, circuit and installation data guide dimensions, material selection and sample review.六针白色端子开口尾线束的结构重点包括插接式端头、端子接入部位、尾线连接形式。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Plug-in connection end插接式端头
- Terminal connection section端子接入部位
- Pigtail connection form尾线连接形式
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the 6-pin white-connector pigtail form as a starting point and confirm these design points against drawings and the actual equipment.以六针白色端子开口尾线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Terminal connection section端子接入部位
Leads use terminal-form ends at the connection points. Orientation, fixing and insulation coverage can follow the equipment assembly.引线以端子形式接入相应连接位置，可按设备装配方式安排端头方向、固定和绝缘覆盖。
Pigtail connection form尾线连接形式
A lead section extends behind the connector, allowing length, further termination and support to follow the equipment connection.插接端后保留引线段，便于按设备接线位置确定长度、后续端接与支撑。
External color scheme外部配色
The external color scheme includes white. Labels and assembly identification can be arranged around the corresponding ends or cable sections.外部配色包含白色，可结合端头或线束段的识别安排标签和装配指示。
Trunk and branch layout主干与分支
Locate trunk and branch datums from equipment fixing points. Allow room for mating, bends and servicing so branches do not transfer installation loads to contacts.以设备固定点确定主干和各支路的尺寸基准，预留插拔、弯曲和维护空间，避免支路把拉力传递到端子。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Full PTFE wire specification and conductor constructionPTFE线材完整规格与导体结构 | Confirm conductor construction and insulation material from the full PTFE wire specification.用完整PTFE线材规格确认导体结构及绝缘材料。 |
|---|---|
| Insulation dimensions, temperature and voltage evidence绝缘尺寸、温度与适用电压依据 | Record insulation dimensions, temperature conditions and voltage basis separately.分别记录绝缘尺寸、温度条件与电压依据。 |
| Stripping tool, termination and insulation retention剥皮工具、端接与绝缘保持 | Stripping and termination tooling must control strand damage, recession and insulation retention.剥皮和端接工装需控制伤股、回缩与绝缘保持。 |
| Heat-shrink/molding compatibility and fixing热缩或包胶相容与固定方式 | Review heat-shrink, molding and fixing for material compatibility and thermal conditions.热缩、包胶与固定方式按材料相容和热条件评审。 |
| Installation and operating boundary安装与使用边界 | Provide the exact wire specification, conductor construction, terminal system, route, temperature zones and test requirements.请提供准确线材规范、导体结构、端子体系、布线路径、温区及试验要求。 |
| Sample and release basis样品与放行依据 | Approve materials, tooling, first article and controlled inspection evidence before repeat production.重复生产前确认物料、工装、首件及受控检验证据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Routing boundaries around hot equipment热区设备的布线边界
Separate continuous temperature, peaks and exposure time around hot equipment. Review wire, terminals and protective parts against their own limits. Confirm conductor construction and insulation material from the full PTFE wire specification.热区布线需要区分连续温度、峰值和暴露时间，线材、端子及保护件应按各自限制评审。选配时，用完整PTFE线材规格确认导体结构及绝缘材料。
Instrument inputs and measurement leads仪器输入与测量引线
Start measurement leads from signal type, input conditions and grounding. Select pairs and shields for the actual measurement range and noise target. Record insulation dimensions, temperature conditions and voltage basis separately.测量引线以信号类型、输入条件和接地方式为起点，线对与屏蔽选择需要对应实际量程和噪声目标。选配时，分别记录绝缘尺寸、温度条件与电压依据。
Shield layers and end terminations屏蔽层与端部接续
Define shield coverage, drain wires and grounding method. Treat shield-continuity checks and system interference testing as separate tasks. Stripping and termination tooling must control strand damage, recession and insulation retention.屏蔽选择需要明确覆盖结构、排流线和接地方式，屏蔽连续性检查与整机抗干扰试验应分别定义。选配时，剥皮和端接工装需控制伤股、回缩与绝缘保持。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Review heat-shrink, molding and fixing for material compatibility and thermal conditions.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，热缩、包胶与固定方式按材料相容和热条件评审。
Routing and retention in confined spaces狭小空间的布线与固定
Define bends, retention points and assembly order in confined spaces. Do not compensate for an incorrect interface direction or length with forced folds. Confirm conductor construction and insulation material from the full PTFE wire specification.狭小空间布线需明确转弯、固定点和拆装顺序，不能用强行折线弥补接口方向或长度误差。选配时，用完整PTFE线材规格确认导体结构及绝缘材料。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Record insulation dimensions, temperature conditions and voltage basis separately.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，分别记录绝缘尺寸、温度条件与电压依据。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports ptfe cable termination projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕PTFE电缆端接的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define termination and protection boundaries确定端接与保护边界
Confirm conductor construction and insulation material from the full PTFE wire specification. The PTFE category name does not establish a temperature rating.用完整PTFE线材规格确认导体结构及绝缘材料。 PTFE类别名称不能证明具体额定温度。
Match dimensions and operating motion配合尺寸与使用动作
Record insulation dimensions, temperature conditions and voltage basis separately. Distinguish PTFE from other fluoropolymers by specification.分别记录绝缘尺寸、温度条件与电压依据。 PTFE与其他含氟材料需按规格区分。
Verify processing and finished condition验证工艺与成品状态
Stripping and termination tooling must control strand damage, recession and insulation retention. Inspect strand damage and insulation recession after stripping.剥皮和端接工装需控制伤股、回缩与绝缘保持。 剥皮伤股和绝缘回缩需检查。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does the PTFE name define the service temperature?PTFE名称能确定使用温度吗？
The PTFE category name does not establish a temperature rating. Confirm conductor construction and insulation material from the full PTFE wire specification.PTFE类别名称不能证明具体额定温度。用完整PTFE线材规格确认导体结构及绝缘材料。
Can other fluoropolymer insulation directly replace PTFE?其他含氟绝缘能直接替代PTFE吗？
Distinguish PTFE from other fluoropolymers by specification. Record insulation dimensions, temperature conditions and voltage basis separately.PTFE与其他含氟材料需按规格区分。分别记录绝缘尺寸、温度条件与电压依据。
What needs particular attention in PTFE termination?PTFE端接重点检查什么？
Inspect strand damage and insulation recession after stripping. Stripping and termination tooling must control strand damage, recession and insulation retention.剥皮伤股和绝缘回缩需检查。剥皮和端接工装需控制伤股、回缩与绝缘保持。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the 6-pin white-connector pigtail. We can use them to review configuration and sample requirements.提供六针白色端子开口尾线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。