D-Sub interface endD-Sub接口端
The D-Sub-form end allows equipment connection to be arranged around the mating face, fixing screws and rear cable route.端头采用D-Sub形式，可围绕插合面、固定螺钉和后部线缆走向安排设备连接。
Measurement Instrument Cable测量仪器电缆
D-sub & Coaxial Connector Mixed HarnessD-SUB与同轴接头混合线束
D-sub & Coaxial Connector Mixed Harness combines d-sub interface end, end transition layout, plug-in connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.D-SUB与同轴接头混合线束的结构重点包括D-Sub接口端、端头转接与组合、插接式端头。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- D-Sub interface endD-Sub接口端
- End transition layout端头转接与组合
- Plug-in connection end插接式端头
CONSTRUCTION结构解析
Conductor, insulation and material choices导体、绝缘与选材要点
Use the d-sub & coaxial connector mixed harness form as a starting point and confirm these design points against drawings and the actual equipment.以D-SUB与同轴接头混合线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Signal path信号路径
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Measurement signal, range and noise target测量信号、量程与噪声目标 | Record measurement signal, range, bandwidth and noise targets.记录测量信号、量程、带宽及噪声目标。 |
|---|---|
| Pairs, shielding, capacitance and leakage requirements线对、屏蔽、电容与漏电要求 | Define pairs, shielding, capacitance and leakage for the instrument input.线对、屏蔽、电容与漏电要求按仪器输入定义。 |
| Thermocouple or special conductor materials热电偶或特殊导体材料 | Confirm special conductors or compensation wire with exact material documents.特殊导体或补偿导线须用准确材料文件确认。 |
| Fixed/moving use, termination and grounding固定运动方式、端接和接地 | Review fixed or moving duty, termination and reference grounding together.固定或运动条件、端接和参考接地共同审核。 |
| Installation and operating boundary安装与使用边界 | Provide sensor, range, bandwidth, accuracy, route, connectors and calibration boundary.请提供传感器、量程、带宽、精度、路径、接口与校准边界。 |
| Sample and release basis样品与放行依据 | Release records the configured measurement lead and agreed evidence.放行记录包含实际配置测量引线与约定证据。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Instrument inputs and measurement leads仪器输入与测量引线
Start measurement leads from signal type, input conditions and grounding. Select pairs and shields for the actual measurement range and noise target. Record measurement signal, range, bandwidth and noise targets.测量引线以信号类型、输入条件和接地方式为起点，线对与屏蔽选择需要对应实际量程和噪声目标。选配时，记录测量信号、量程、带宽及噪声目标。
External interfaces on portable equipment便携设备的外部接口
Consider handling, plug grip and cable bends together. Align the exit direction with the device position during use. Define pairs, shielding, capacitance and leakage for the instrument input.便携设备连接要同时考虑操作手势、插头握持和尾部弯曲空间，线缆出口方向应与实际使用姿态协调。选配时，线对、屏蔽、电容与漏电要求按仪器输入定义。
Routing boundaries around hot equipment热区设备的布线边界
Separate continuous temperature, peaks and exposure time around hot equipment. Review wire, terminals and protective parts against their own limits. Confirm special conductors or compensation wire with exact material documents.热区布线需要区分连续温度、峰值和暴露时间，线材、端子及保护件应按各自限制评审。选配时，特殊导体或补偿导线须用准确材料文件确认。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Review fixed or moving duty, termination and reference grounding together.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，固定或运动条件、端接和参考接地共同审核。
Equipment control-board connections设备控制板连接
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Record measurement signal, range, bandwidth and noise targets.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，记录测量信号、量程、带宽及噪声目标。
Module connections in laboratory equipment实验室设备的模块配线
Coordinate sample areas, moving mechanisms and serviceable modules in laboratory equipment. Take isolation and cleaning requirements from the target device documents. Define pairs, shielding, capacitance and leakage for the instrument input.实验设备连接需要协调样品区、运动机构和可维护模块，电气隔离与清洁要求应来自目标设备文件。选配时，线对、屏蔽、电容与漏电要求按仪器输入定义。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports measurement instrument cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕测量仪器电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define conductors and layer construction定义导体与层结构
Record measurement signal, range, bandwidth and noise targets. Ordinary copper wire cannot replace specified compensating cable.记录测量信号、量程、带宽及噪声目标。 普通铜线不能替代指定补偿导线。
Match the actual installation duty匹配实际敷设工况
Define pairs, shielding, capacitance and leakage for the instrument input. A low-noise label needs measurement conditions.线对、屏蔽、电容与漏电要求按仪器输入定义。 电缆低噪声名称需有测量条件。
Confirm material and inspection documents确认材料与检验文件
Confirm special conductors or compensation wire with exact material documents. Do not arbitrarily connect shields to instrument reference ground.特殊导体或补偿导线须用准确材料文件确认。 屏蔽与仪器参考地不得随意并接。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Can ordinary copper wire replace compensation wire?普通铜线可以替代补偿导线吗？
Ordinary copper wire cannot replace specified compensating cable. Record measurement signal, range, bandwidth and noise targets.普通铜线不能替代指定补偿导线。记录测量信号、量程、带宽及噪声目标。
Can a low-noise designation be treated as a measurement result?低噪声名称能直接作为测量结果吗？
A low-noise label needs measurement conditions. Define pairs, shielding, capacitance and leakage for the instrument input.电缆低噪声名称需有测量条件。线对、屏蔽、电容与漏电要求按仪器输入定义。
Can a shield be connected freely to the instrument reference ground?屏蔽可以任意接到仪器参考地吗？
Do not arbitrarily connect shields to instrument reference ground. Confirm special conductors or compensation wire with exact material documents.屏蔽与仪器参考地不得随意并接。特殊导体或补偿导线须用准确材料文件确认。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the d-sub & coaxial connector mixed harness. We can use them to review configuration and sample requirements.提供D-SUB与同轴接头混合线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。