FI-RE LVDS Double-Ended Harness can be configured around equipment interfaces and routing. Match the complete connector series, mating pair and application requirements.FI-RE接口 · LVDS双端连接线束可围绕设备接口与安装路径进行配置。匹配完整接头系列、对插件及应用要求。
Use the fi-re lvds double-ended harness form as a starting point and confirm these design points against drawings and the actual equipment.以FI-RE接口 · LVDS双端连接线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
Similar contact rows do not establish same-series mating相似针排不确定同系列插合
Check contact retention separately from harness pull strength端子保持与线束拉力分别核对
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Exact JAE series, housing and terminal part numbersJAE具体系列、插壳与端子料号 | Record the JAE family, housing and contact part numbers together.同时记录JAE系列、壳体及端子件号。 |
|---|---|
| Contact arrangement, polarization and mating end针位排列、极化和对插端 | Define contact rows, polarization and mates from controlled end views.按受控端视图定义针排、极化及对插端。 |
| Insulation diameter, conductor size and termination process绝缘外径、线径与端接工艺 | Match termination method and tooling to conductor and insulation dimensions.端接方式与导体、绝缘外径和工装相匹配。 |
| Locking, protection and installation envelope锁止、防护与安装包络 | Check locking, retention and installation envelope as separate requirements.检查锁止、保持力及安装包络的不同边界。 |
| Installation and operating boundary安装与使用边界 | Supply part numbers, pinout, dimensions, environment and required evidence.提供料号、针脚、尺寸、环境及所需证据。 |
| Sample and release basis样品与放行依据 | Review materials and drawings, approve samples, then release controlled production.审核材料与图纸，认可样品后放行受控生产。 |
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Record the JAE family, housing and contact part numbers together.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，同时记录JAE系列、壳体及端子件号。
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Define contact rows, polarization and mates from controlled end views.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，按受控端视图定义针排、极化及对插端。
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Match termination method and tooling to conductor and insulation dimensions.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，端接方式与导体、绝缘外径和工装相匹配。
Check insertion direction, contact orientation and frame clearance at display modules. Mark fixed folds on the assembly drawing. Check locking, retention and installation envelope as separate requirements.显示模块连接需核对插入方向、触点朝向与边框空间，并将固定折弯的位置标入装配图。选配时，检查锁止、保持力及安装包络的不同边界。
Select power branches from actual loads, circuit protection and route length. Include termination, retention and service positions in the wiring definition. Record the JAE family, housing and contact part numbers together.供电分支以实际负载、回路保护和线长为选配依据，端头、固定和检修位置也需列入布线定义。选配时，同时记录JAE系列、壳体及端子件号。
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Define contact rows, polarization and mates from controlled end views.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，按受控端视图定义针排、极化及对插端。
Our China factory supports jae compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕JAE兼容组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Record the JAE family, housing and contact part numbers together. Similar contact rows do not establish same-series mating.同时记录JAE系列、壳体及端子件号。 相似针排不确定同系列插合。
Define contact rows, polarization and mates from controlled end views. Check contact retention separately from harness pull strength.按受控端视图定义针排、极化及对插端。 端子保持与线束拉力分别核对。
Match termination method and tooling to conductor and insulation dimensions. Alternatives require dimensional and mating verification.端接方式与导体、绝缘外径和工装相匹配。 替代件需具体尺寸和插合验证。
Similar contact rows do not establish same-series mating. Record the JAE family, housing and contact part numbers together.相似针排不确定同系列插合。同时记录JAE系列、壳体及端子件号。
Check contact retention separately from harness pull strength. Define contact rows, polarization and mates from controlled end views.端子保持与线束拉力分别核对。按受控端视图定义针排、极化及对插端。
Alternatives require dimensional and mating verification. Match termination method and tooling to conductor and insulation dimensions.替代件需具体尺寸和插合验证。端接方式与导体、绝缘外径和工装相匹配。
Share mating interfaces, a circuit table, target lengths or a sample for the fi-re lvds double-ended harness. We can use them to review configuration and sample requirements.提供FI-RE接口 · LVDS双端连接线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。
