Interface and function review接口与功能确认
Similar contact rows do not establish same-series mating相似针排不确定同系列插合
JAE CompatibleJAE兼容组件
FI-RE51P Display Double-Ended HarnessFI-RE51P接口 · 显示器双端连接线束
FI-RE51P Display Double-Ended Harness can be configured around equipment interfaces and routing. Custom JAE-interface wiring for vehicle controls, displays and equipment modules, with defined pinouts, materials and inspection.FI-RE51P接口 · 显示器双端连接线束可围绕设备接口与安装路径进行配置。定制 JAE 接口布线，覆盖车载控制、显示及设备模块，明确针脚、材料和检验。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the fi-re51p display double-ended harness form as a starting point and confirm these design points against drawings and the actual equipment.以FI-RE51P接口 · 显示器双端连接线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Installation and acceptance安装与验收
Check contact retention separately from harness pull strength端子保持与线束拉力分别核对
Manufacturing reference制造依据
Confirm drawings, circuit mapping, dimensional datums and sample revision before manufacture to control fit checks and repeat production.确认图纸、连接关系、尺寸基准和样品版本后再制作，减少试装与重复生产中的差异。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Exact JAE series, housing and terminal part numbersJAE具体系列、插壳与端子料号 | Record the JAE family, housing and contact part numbers together.同时记录JAE系列、壳体及端子件号。 |
|---|---|
| Contact arrangement, polarization and mating end针位排列、极化和对插端 | Define contact rows, polarization and mates from controlled end views.按受控端视图定义针排、极化及对插端。 |
| Insulation diameter, conductor size and termination process绝缘外径、线径与端接工艺 | Match termination method and tooling to conductor and insulation dimensions.端接方式与导体、绝缘外径和工装相匹配。 |
| Locking, protection and installation envelope锁止、防护与安装包络 | Check locking, retention and installation envelope as separate requirements.检查锁止、保持力及安装包络的不同边界。 |
| Installation and operating boundary安装与使用边界 | Supply part numbers, pinout, dimensions, environment and required evidence.提供料号、针脚、尺寸、环境及所需证据。 |
| Sample and release basis样品与放行依据 | Review materials and drawings, approve samples, then release controlled production.审核材料与图纸，认可样品后放行受控生产。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Record the JAE family, housing and contact part numbers together.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，同时记录JAE系列、壳体及端子件号。
Equipment control-board connections设备控制板连接
Document pin-row views, mating direction and nearby wire support. Check access to the latch and contacts after assembly. Define contact rows, polarization and mates from controlled end views.板端连接要给出针排视图、插合方向和近端线缆支撑；检查装配后是否仍能操作锁扣并查看接点。选配时，按受控端视图定义针排、极化及对插端。
Contact and fine-wire termination端子与细线端接
Contact selection depends on conductor construction, insulation diameter and tooling limits. Set wire preparation and crimp inspection for the actual contact part. Match termination method and tooling to conductor and insulation dimensions.端子选择同时取决于导体结构、绝缘外径和工具范围；备线尺寸与压接检查应落到实际接点型号。选配时，端接方式与导体、绝缘外径和工装相匹配。
Display-module and control-board connections显示模块与控制板连接
Check insertion direction, contact orientation and frame clearance at display modules. Mark fixed folds on the assembly drawing. Check locking, retention and installation envelope as separate requirements.显示模块连接需核对插入方向、触点朝向与边框空间，并将固定折弯的位置标入装配图。选配时，检查锁止、保持力及安装包络的不同边界。
Equipment power-distribution branches设备电源分配支路
Select power branches from actual loads, circuit protection and route length. Include termination, retention and service positions in the wiring definition. Record the JAE family, housing and contact part numbers together.供电分支以实际负载、回路保护和线长为选配依据，端头、固定和检修位置也需列入布线定义。选配时，同时记录JAE系列、壳体及端子件号。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Define contact rows, polarization and mates from controlled end views.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，按受控端视图定义针排、极化及对插端。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports jae compatible projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕JAE兼容组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Record the JAE family, housing and contact part numbers together. Similar contact rows do not establish same-series mating.同时记录JAE系列、壳体及端子件号。 相似针排不确定同系列插合。
Define cable and installation conditions定义线材与安装条件
Define contact rows, polarization and mates from controlled end views. Check contact retention separately from harness pull strength.按受控端视图定义针排、极化及对插端。 端子保持与线束拉力分别核对。
Set processing and acceptance requirements确定加工与验收要求
Match termination method and tooling to conductor and insulation dimensions. Alternatives require dimensional and mating verification.端接方式与导体、绝缘外径和工装相匹配。 替代件需具体尺寸和插合验证。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Do similar contact rows establish the same family?相似针排能确定同系列吗？
Similar contact rows do not establish same-series mating. Record the JAE family, housing and contact part numbers together.相似针排不确定同系列插合。同时记录JAE系列、壳体及端子件号。
Are contact retention and harness pull force the same check?端子保持力和线束拉力是同一检查吗？
Check contact retention separately from harness pull strength. Define contact rows, polarization and mates from controlled end views.端子保持与线束拉力分别核对。按受控端视图定义针排、极化及对插端。
How is an alternative interface verified?替代接口需要怎样的验证？
Alternatives require dimensional and mating verification. Match termination method and tooling to conductor and insulation dimensions.替代件需具体尺寸和插合验证。端接方式与导体、绝缘外径和工装相匹配。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the fi-re51p display double-ended harness. We can use them to review configuration and sample requirements.提供FI-RE51P接口 · 显示器双端连接线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。