End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Combined optical and electrical assemblies光纤与电连接组合组件
Fiber & Power Multi-Connector Mixed Harness光纤与电源多接头混合线束
A common jacketed trunk is combined with multiple separate ends. Optical channels and power branches need their own connection maps and acceptance references.共同外护套主干与多路独立端头组合，光通道与电源支路需要各自的连接表和检验依据。
- Separate optical and electrical definitions光、电连接分别定义
- Coordinated trunk and breakout layout主干与分支共同布置
- Define scope and acceptance before sampling项目范围与验收先行确认
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
The combined ends provide a starting point for routing different connection paths together. Define optical, power and other signal functions and acceptance separately; a combined form does not establish optical-electrical conversion.组合端头用于讨论不同连接路径的共同布置。光通道、电源与其他信号的功能及验收分别定义，不凭组合外形推断光电转换。
Plug-in connection end插接式端头
The end uses a plug-in form, with clearance arranged for insertion, removal and cable bends.端头采用插接形式，可围绕安装位置安排插入、退出及线缆弯曲空间。
Multiple connector positions多端头连接位置
Multiple ends provide separate connection positions. Layout and spacing can follow the module arrangement.多个端头提供分别接入的位置，线束展开方向与各端头间距可围绕模块布局定义。
Distinct paths defined separately不同通道独立确认
Confirm optical and electrical ends, maps and acceptance references separately, then coordinate the trunk, branches and labels.光接口与电接口的端头、连接表和验收依据分别确认，再统一安排主干、分支与标识。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Optical interfaces at both ends两端光接口 | Record each connector series, mating part and end-face form. Similar interface names do not replace complete part numbers and distribution-port documents.分别记录两端接头系列、对插件与端面形式；接口名称相近不能替代完整型号和配线端口资料。 |
|---|---|
| Separate optical and electrical paths独立光、电通道 | List fiber type and channel count, power loads and other signal paths separately. Sharing a jacket does not mean the paths share contacts.把光纤类型与通道数、电源负载及其他信号路径分开列入连接表；共同护套不表示不同路径共用接点。 |
| Channel mapping and polarity通道对应与极性 | Define the position and transmit/receive relationship at both ends of every fiber. Include polarity or breakout maps for multifiber and branched assemblies.定义每根光纤两端的位置及收发对应。多芯与分支组件另附极性或分支映射图，避免按外形默认接续顺序。 |
| Length and breakout datums长度与分支基准 | Define measurement points, tolerances and identification positions for the overall cable, fine tails or individual branches. Allow enough length for equipment mating and removal.明确总长、端部细尾段或各支路的测量起止点、公差及标识位置，并保留设备插拔所需余量。 |
| Hybrid routing and protection混合布线与保护 | Arrange trunks and breakouts around fiber bending limits, electrical insulation and end retention. Define jackets, shielding and strain support for their respective paths.围绕光纤弯曲边界、电路绝缘要求和各端头固定位置安排主干与分支，分别确认护套、屏蔽和应力支撑。 |
| End-face and optical acceptance端面与光学验收条件 | Agree end-face cleanliness, channel checks and any required optical test conditions, limits and reporting responsibility at project start for the selected interface and cable configuration.在项目开始时约定端面清洁、通道核对及所需光学测试条件、限值和报告责任，并对应所选接口与光缆配置。 |
APPLICATIONS连接的应用
Application directions应用方向
The following directions cover equipment connections and distribution routes. Define optical interfaces, channels and optical acceptance from the specific system documents.以下连接方向围绕设备与配线路径展开。所选光接口、通道及光学验收要求以具体系统资料为依据。
Fiber-distribution panels机房光纤配线面板
At fiber-distribution panels, arrange connector orientation, boot clearance and service allowance around port positions. Confirm the connector series, end-face form and channel identification against the distribution record before defining each jumper.光配线面板的跳接需按端口位置安排端头方向、尾套空间与可拆卸余量。接头系列、端面形式和通道编号与配线记录一起确认。
Optical-port jumpers for network equipment网络设备光口跳接
For short links between equipment optical ports and the distribution side, review mating ends, transmit/receive direction and bend clearance. Use equipment-port documents to establish channel mapping rather than inferring it from housing colors.设备光口与配线侧之间的短距离连接，重点是端头对插、发送接收方向和弯曲空间。通道对应以设备端口资料为准，不用外壳颜色推断。
Separate optical paths at optical modules光模块侧的独立光通道
In a mixed-connection project, define optical interfaces, channels and equipment-side jumpers at the optical module separately. Route independent power or other signals from their own maps. Shared jackets and breakouts do not establish shared contacts or built-in optical-electrical conversion.混合连接项目在光模块侧分别确认光接口、通道和设备端跳线，独立电源或其他信号按各自连接表布置。共同护套与分支结构不表示光通道和电路共用接点，也不等于自带光电转换。
Vertical cable-management paths机柜竖向理线路径
Vertical cabinet routes need space for turns, supports and servicing. Use the selected optical cable documents to set bending and tensile limits, and keep stored slack separate from equipment airflow and removable-module access.竖向布线路径需要为转弯、固定和维护留出空间。按所选光缆规定弯曲与拉力边界，并将余长收纳位置与设备风道、可拆模块分开安排。
Combined links across cabinet modules机柜多模块组合连接
When cabinet modules use different interfaces, coordinate end positions and labels in one assembly drawing. Retain separate maps for optical channels, power and other signals so each connection purpose can be checked during installation.机柜内模块使用不同接口时，可在装配图中统一安排端头位置与标签。光通道、电源及其他信号仍各有对应表，安装人员能够逐路核对连接用途。
Optical-link projects in video equipment rooms视频机房光链路项目
For video-room projects that specify optical interfaces, plan jumpers around equipment racks, distribution panels and service aisles. Establish optical-module selection, signal format and link acceptance from system requirements; cable form alone does not establish video-format support.采用光接口的视频机房项目，可结合设备机架、配线面板和维修通道安排跳接。光模块、信号制式和链路验收按系统要求确定，线缆外形不代表视频格式支持。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
China factory · electrical and combined-project support中国工厂 · 电连接与组合项目支持
Our China factory provides custom wire harness manufacturing and OEM/ODM project support. For projects involving optical connections, define electrical manufacture, optical materials and termination, installation assembly and optical acceptance as separate scopes before agreeing samples and delivery documents.Super Smile-Tech中国工厂提供定制线束制造与OEM/ODM项目支持。涉及光连接的组合需求，分别确认电连接制造、光纤物料与端接、安装装配及光学验收的执行范围，再确定样品方案与交付文件。
Separate optical and electrical interface maps光、电接口分表
Create optical-channel and power or other signal maps from equipment documents. Define each end function before combining them in an assembly drawing and identification plan.以设备资料分别建立光通道映射、电源或其他信号连接表，明确各端头用途，再整理为统一的装配图与标识方案。
Length and protection layout长度与保护布置
Set overall length, fine-tail length, breakout positions and jacket sections around the rack route. Include supports, bending limits and service allowance in the approval drawing.围绕机架路径调整总长、细尾长度、分支位置和护套段落，并把固定、弯曲与维护余量写入确认图。
Samples and project acceptance样品与项目验收
Use the sample stage to review interface assembly, channel records and installed dimensions. Agree the scope for optical termination, optical testing and reports on the specific project.样品阶段分别确认接口装配、通道资料和安装尺寸；光纤端接方式、光学测试与报告要求按项目商定范围执行。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Do mixed ends establish built-in optical-electrical conversion?混合端头是否表示线缆自带光电转换？
They do not. Equipment block diagrams and circuit documents must establish the interface functions. If the project includes an active conversion module, define its supply, protocol and validation scope separately.不能这样判断。需要设备功能框图与电路资料确认各接口用途；如果项目含有源转换模块，其供电、协议和验证范围必须另行定义。
How are channels kept in the correct order?多芯或双芯组件如何避免通道接反？
Create a map from end-port views, transmit/receive definitions and channel IDs. For MPO or breakout structures, also specify polarity and branch order in the acceptance records.用两端端口视图、收发定义及通道编号建立映射。MPO或分支结构还需约定极性与分支排序，并在项目验收记录中体现。
What defines optical acceptance for a project?需要哪些资料才能确认光学验收？
Provide the fiber type, connector and end-face requirements, plus the system-defined test wavelengths, limits and reporting requirements. Confirm responsibility for termination, testing and reports before sampling.提供所选纤型、接头与端面要求，以及系统规定的测试波长、限值和报告要求。端接、检测与报告的执行责任在样品前确认。
Start with optical interfaces and the routing plan从光接口与布线路径开始
Share the equipment block diagram, optical interfaces and channel map, power or other signal maps, and trunk and branch dimensions to define the mixed assembly and validation scope.提供设备功能框图、光接口和通道表、电源或其他信号连接表，以及主干与分支尺寸，明确混合连接的装配和验证边界。