Circular connection end圆形连接端
The end uses a circular interface form, with connection positions planned around mating direction, retention and cable exit.端头具有圆形接口形式，可围绕对插方向、端部固定和线缆出口规划连接位置。
Harting Interface Cable ProjectHarting接口电缆项目
Han16B Rectangular Connector to 4-Way Circular Socket HarnessHan16B接口 · 矩形接头转四路圆形插座线束
Han16B Rectangular Connector to 4-Way Circular Socket Harness combines circular connection end, rectangular interface form, end transition layout. Interface, circuit and installation data guide dimensions, material selection and sample review.Han16B接口 · 矩形接头转四路圆形插座线束的结构重点包括圆形连接端、矩形接口外形、端头转接与组合。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Circular connection end圆形连接端
- Rectangular interface form矩形接口外形
- End transition layout端头转接与组合
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the han16b rectangular connector to 4-way circular socket harness form as a starting point and confirm these design points against drawings and the actual equipment.以Han16B接口 · 矩形接头转四路圆形插座线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Rectangular interface form矩形接口外形
The rectangular interface form allows end position and service clearance to follow the mating face, latch and cable exit.接口采用矩形轮廓，可围绕插入面、卡扣与线束出口安排端头位置和拆装空间。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Harting series, frame and module configurationHarting系列、框架与模块配置 | Confirm the Harting family, frame and installation order of every module.确认Harting系列、框架及每个模块的安装顺序。 |
|---|---|
| Housing size, latch and mounting style外壳尺寸、锁扣及安装形式 | Define housing size, latch and panel fixing around assembly clearance.外壳尺寸、锁扣和面板固定按总装空间定义。 |
| Contacts, wire sizes and power/signal allocation接点、线径与动力信号分区 | Assign power, signal and ground contacts to the actual conductors and modules.动力、信号和接地接点对应实际线径与模块。 |
| Cable entry, grounding and shielding backshell电缆入口、接地和屏蔽尾壳 | Document cable entry, backshell, housing ground and cable shield separately.入口、尾壳、壳体接地与电缆屏蔽分别记录。 |
| Installation and operating boundary安装与使用边界 | For quotation, provide the Han series and housing size; part numbers for each hood, base, insert or module and contact; mating-face view, pin and circuit map, load and voltage, conductors and jacket, cable-exit direction, gland and latch choice, environment, quantity and acceptance criteria. Compatible work does not imply HARTING authorization or certification.询价请提供 Han 系列与外壳尺寸、每个外壳／底座／插芯或模块／触点的料号、对插面视图、针脚与回路表、负载与电压、导体和护套、出线方向、格兰头与锁扣形式、安装环境、数量及验收要求。品牌兼容不代表 HARTING 授权或认证。 |
| Sample and release basis样品与放行依据 | Approved inputs become a controlled BOM, circuit drawing, termination and assembly instructions, first-article checkpoints and agreed inspections. Check insert orientation, contact position and seating, latch closure, cable-entry retention, length and continuity. IP, vibration or rated-load performance requires the exact product data and separately defined project evidence.经客户确认后形成受控物料表、回路图、端接与装配指引、首件核对点和约定检验项目。重点核对插芯朝向、接点位置、触点入位、锁扣闭合、进线夹持、线长与导通；IP、防振或额定负载表现须按准确产品资料与项目试验单独证明。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Rectangular interfaces and module layouts矩形接口与模块排列
Check insert orientation, latch access and module order in rectangular interfaces. Identify power and signal circuits separately in the contact table. Confirm the Harting family, frame and installation order of every module.矩形重载接口需要核对插芯朝向、锁扣操作和模块顺序，动力与信号回路应在接点表中分别标明。选配时，确认Harting系列、框架及每个模块的安装顺序。
Equipment panels and circular interfaces设备面板与圆形接口
Start with the cutout, panel thickness, mounting direction and rear clearance. Coordinate contact arrangement and cable exit with the complete assembly view. Define housing size, latch and panel fixing around assembly clearance.面板连接以开孔、板厚、装配方向和后方净空为起点；接点排列与电缆出口还需要对应完整总装视图。选配时，外壳尺寸、锁扣和面板固定按总装空间定义。
Internal machine connections and service设备机内连接与维护
Keep internal connections clear of working zones and moving parts. Allow appropriate cable length between supports, interfaces and service paths. Assign power, signal and ground contacts to the actual conductors and modules.设备机内连接要避开加工区与运动部件，并在固定点、接口和检修路径之间保留合理线缆余量。选配时，动力、信号和接地接点对应实际线径与模块。
Equipment power-distribution branches设备电源分配支路
Select power branches from actual loads, circuit protection and route length. Include termination, retention and service positions in the wiring definition. Document cable entry, backshell, housing ground and cable shield separately.供电分支以实际负载、回路保护和线长为选配依据，端头、固定和检修位置也需列入布线定义。选配时，入口、尾壳、壳体接地与电缆屏蔽分别记录。
Terminal wiring inside control cabinets控制柜内的端子配线
Coordinate terminal positions, duct exits and service access within the cabinet. Wire labels should correspond to the circuit table and equipment ports. Confirm the Harting family, frame and installation order of every module.柜内连接需协调端子位置、线槽出口和可维护空间，线号应能对应回路表与设备端口。选配时，确认Harting系列、框架及每个模块的安装顺序。
Module wiring within enclosures机箱内部的模块配线
Coordinate board positions, module removal and wire bends within the enclosure. Preserve insulation clearance and support behind each termination. Define housing size, latch and panel fixing around assembly clearance.机箱内部配线需要协调板卡位置、模块拆装和导线转弯空间；端接后的绝缘与支撑不能被外壳挤压。选配时，外壳尺寸、锁扣和面板固定按总装空间定义。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports harting interface cable project projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕Harting接口电缆项目的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Check the interface and matching parts核对接口与配套件
Confirm the Harting family, frame and installation order of every module. Heavy-duty shell shape does not establish matching internal modules.确认Harting系列、框架及每个模块的安装顺序。 重载外壳外形不能证明内部模块一致。
Define cable and installation conditions定义线材与安装条件
Define housing size, latch and panel fixing around assembly clearance. Confirm insert sequence and keying as a set.外壳尺寸、锁扣和面板固定按总装空间定义。 插芯序列与键位需成套确认。
Set processing and acceptance requirements确定加工与验收要求
Assign power, signal and ground contacts to the actual conductors and modules. Record earth contacts and housing grounding separately.动力、信号和接地接点对应实际线径与模块。 接地接点和壳体接地需分开记录。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Do equal housings mean the internal modules match?外壳相同是否意味着内部模块相同？
Heavy-duty shell shape does not establish matching internal modules. Confirm the Harting family, frame and installation order of every module.重载外壳外形不能证明内部模块一致。确认Harting系列、框架及每个模块的安装顺序。
Why confirm module order and keying as a set?模块顺序和键位为什么要成套确认？
Confirm insert sequence and keying as a set. Define housing size, latch and panel fixing around assembly clearance.插芯序列与键位需成套确认。外壳尺寸、锁扣和面板固定按总装空间定义。
Can ground contacts and housing ground be recorded as one item?接地接点和壳体接地可以合并记录吗？
Record earth contacts and housing grounding separately. Assign power, signal and ground contacts to the actual conductors and modules.接地接点和壳体接地需分开记录。动力、信号和接地接点对应实际线径与模块。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the han16b rectangular connector to 4-way circular socket harness. We can use them to review configuration and sample requirements.提供Han16B接口 · 矩形接头转四路圆形插座线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。