Terminal connection section端子接入部位
Leads use terminal-form ends at the connection points. Orientation, fixing and insulation coverage can follow the equipment assembly.引线以端子形式接入相应连接位置，可按设备装配方式安排端头方向、固定和绝缘覆盖。
Outdoor Waterproof Harness户外防水线束
Irrigation Equipment Terminals Pigtail灌溉设备接线端子尾线
Irrigation Equipment Terminals Pigtail combines terminal connection section, pigtail connection form. Interface, circuit and installation data guide dimensions, material selection and sample review.灌溉设备接线端子尾线的结构重点包括端子接入部位、尾线连接形式。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the irrigation equipment terminals pigtail form as a starting point and confirm these design points against drawings and the actual equipment.以灌溉设备接线端子尾线的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Pigtail connection form尾线连接形式
A lead section extends behind the connector, allowing length, further termination and support to follow the equipment connection.插接端后保留引线段，便于按设备接线位置确定长度、后续端接与支撑。
Trunk and branch layout主干与分支
Locate trunk and branch datums from equipment fixing points. Allow room for mating, bends and servicing so branches do not transfer installation loads to contacts.以设备固定点确定主干和各支路的尺寸基准，预留插拔、弯曲和维护空间，避免支路把拉力传递到端子。
Interface and function review接口与功能确认
Ingress ratings require complete-assembly test evidence防水等级必须有完整组件和试验依据
Installation and acceptance安装与验收
Check ingress paths beyond connector and wire seals连接器与线封之外的进水路径需检查
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Ingress conditions, installed orientation and mating state目标进水条件、安装姿态与对插状态 | Define ingress targets for the complete assembly, mating state and orientation.进水目标结合完整组件、插合状态与安装姿态。 |
|---|---|
| Connector seals and wire-seal diameter range连接器密封件、线封适用外径 | Match seals to actual insulation and jacket diameters.线封与密封件匹配实际绝缘及护套外径。 |
| Sealing of splices, cable exits and unused cavities接续、出线口和未使用孔位密封 | Review cable exits, splices and unused cavities as separate sealing paths.出线口、接续和空孔作为独立密封路径审核。 |
| Outdoor temperature, UV and chemical exposure户外温度、紫外线与化学暴露 | Select materials for sunlight, temperature, fluids and movement together.材料同时考虑日照、温度、液体与运动。 |
| Circuit and revision reference电路与版本依据 | Define the actual exposure, target protection level or test method, mated connector system, cable diameter, unused cavities, mounting direction, branch treatment and responsibility for final installed validation.需要明确实际暴露环境、目标防护等级或测试方法、完整对插系统、线缆外径、空腔处理、安装方向、分支防护以及最终装机验证责任。 |
| Sample and manufacturing configuration样品与制造配置 | The sealing stack and cable-entry dimensions are reviewed before the sample. Assembly controls, continuity and any agreed ingress test are recorded for the project; no universal waterproof claim is made outside that validated configuration.打样前审核密封组合和出线尺寸，项目中记录装配控制、导通和约定的防护测试；未经该配置验证，不作通用防水承诺。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Outdoor equipment interfaces and fixing室外设备接口与固定
For outdoor electrical equipment, review interfaces, cable outlets and fixing points together, including moisture-entry paths and access for service. Define ingress targets for the complete assembly, mating state and orientation.室外电气设备的接口、线缆出口与固定点需成套确认，明确水汽进入路径和可维护空间。选配时，进水目标结合完整组件、插合状态与安装姿态。
Construction and mobile machinery auxiliaries工程与移动机械辅助系统
Supports defined low-voltage controls, lighting, sensors and attachments exposed to vibration, mud and service handling. Match seals to actual insulation and jacket diameters.支持受振动、泥污与检修操作影响的低压控制、照明、传感器和附件。选配时，线封与密封件匹配实际绝缘及护套外径。
Cable routes on moving mechanisms移动机构的线缆路径
Check travel, bend paths, fixing points and end loads for moving-equipment leads. Outdoor protection requirements need a separate review. Review cable exits, splices and unused cavities as separate sealing paths.移动设备的连接线需核对运动行程、弯曲路径、固定点和端部受力，再单独确认室外防护要求。选配时，出线口、接续和空孔作为独立密封路径审核。
Agricultural and processing equipment农业与加工设备
Addresses washdown, dust, moisture and replaceable field connections on handling and processing equipment when specifically defined. Select materials for sunlight, temperature, fluids and movement together.针对搬运与加工设备明确的冲洗、粉尘、湿气与可更换现场接口需求。选配时，材料同时考虑日照、温度、液体与运动。
Outdoor-equipment service connections室外设备的维修连接
Service harnesses for pumps and other exposed equipment need accessible interfaces, suitable outlet directions, fixing and a review of moisture exposure. Define ingress targets for the complete assembly, mating state and orientation.水泵与其他外露设备的维修线束需兼顾接口可接近性、出线方向、固定方式及潮湿环境。选配时，进水目标结合完整组件、插合状态与安装姿态。
Outdoor monitoring and measurement户外监测与测量
Connects probes, instruments, communication nodes and service ports where signal integrity and environmental sealing must coexist. Match seals to actual insulation and jacket diameters.连接探头、仪器、通信节点与服务接口，使信号完整性与环境密封同时满足。选配时，线封与密封件匹配实际绝缘及护套外径。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports outdoor waterproof harness projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕户外防水线束的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Define the actual exposure before selecting parts选件前先定义真实暴露
Rain, immersion, pressure wash, mud, salt, chemicals, UV and condensation are different duties. The project states which conditions and test references apply.雨淋、浸水、压力冲洗、泥污、盐、化学、紫外与冷凝属于不同工况，项目需要明确适用条件和测试依据。
Review the complete mated interface审核完整插合接口
Both halves, seals, terminals, cavity plugs, locks, backshells and cable entry are reviewed together, including responsibility for the equipment-side connector.对插两端、密封、端子、堵孔、锁止、尾壳与出线共同审核，并明确设备端接口责任。
Control branch joints and low points控制分支接点与积水低点
Splices, breakouts and label positions are arranged so capillary paths, unsupported bends and water collection do not undermine the sealed interfaces.安排接点、分支与标签位置，避免毛细路径、无支撑弯曲与积水破坏密封接口。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Is a waterproof connector enough to make the harness waterproof?使用防水连接器就代表整条线束防水吗？
No. Both mated halves, seals, cavity plugs, wire diameters, cable entries, branches, strain relief and installed orientation affect the complete result.不代表。对插两端、密封、堵孔、线径、出线、分支、应力消除与安装方向都会影响完整结果。
Can you provide a specific IP rating?可以提供指定IP等级吗？
A target can be reviewed when the complete configuration, specimen, test method and acceptance criteria are defined. The category name alone is not an IP claim.完整配置、试样、测试方法与验收标准明确后可以审核目标，小类名称本身不构成IP等级承诺。
What information is needed for development?开发需要哪些资料？
Provide both mating interfaces, pin map, wire and cable diameters, unused cavities, installation direction, exposure, movement, quantity and the required test reference.请提供对插两端、针脚、线材与电缆外径、空腔、安装方向、暴露、运动、数量与所需测试依据。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the irrigation equipment terminals pigtail. We can use them to review configuration and sample requirements.提供灌溉设备接线端子尾线的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。