M12 circular interface formM12圆形接口形式
The M12-form circular end can be oriented around the equipment mating position, handling clearance and cable exit.M12形式的圆形接入端可结合设备对插位置安排方向、操作空间与出线位置。
Harting Interface Cable ProjectHarting接口电缆项目
M12 to RJ45 Network HarnessM12转RJ45网络线束
M12 to RJ45 Network Harness combines m12 circular interface form, rj45 connection end, end transition layout. Interface, circuit and installation data guide dimensions, material selection and sample review.M12转RJ45网络线束的结构重点包括M12圆形接口形式、RJ45连接端、端头转接与组合。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- M12 circular interface formM12圆形接口形式
- RJ45 connection endRJ45连接端
- End transition layout端头转接与组合
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the m12 to rj45 network harness form as a starting point and confirm these design points against drawings and the actual equipment.以M12转RJ45网络线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
RJ45 connection endRJ45连接端
The RJ45-form end supports routing around port direction, latch access and cable exit.端头采用RJ45形式，可围绕端口朝向、锁扣操作和线缆出口安排设备连接。
End transition layout端头转接与组合
The assembly organizes a transition or combined connection, with end directions, transition sections and fixing arranged around the equipment positions.组件以转接或组合形式组织连接，可围绕两端设备位置安排端头方向、过渡段与固定。
Signal path信号路径
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Both interfaces and complete part numbers两端接口与完整料号 | Define the full family, orientation and mating parts for both ends, such as RJ45, IX or M12. A brand name does not define the interface.明确RJ45、IX或M12等两端接口的完整系列、方向与对插件，不以品牌名称替代接口定义。 |
|---|---|
| Pins, pairs and signal definition针脚、线对与信号定义 | Record pin and pair mapping on both sides, equipment signal requirements and the target communication rate.记录双方针脚与线对对应、设备信号要求和目标通信速率。 |
| Cable construction, length and shielding线缆结构、长度与屏蔽 | Select pairs, impedance, shielding and length for the target link. Confirm complete-assembly capability with both devices.按目标链路选配线对结构、阻抗、屏蔽及长度，完整组件能力需结合两端设备确认。 |
| Retention, cable exits and installation space锁紧、出线与安装空间 | Check latch or threaded retention, jacket diameter, exit direction and rear bend and service clearance.核对锁扣或螺纹锁紧、护套外径、出线方向及后方弯曲和维护空间。 |
| Network equipment and power boundary网络设备与供电边界 | Provide device ports, network function, a pin map, length and installation environment. Define circuits and validation separately if PoE or another power function is required.提供设备端口、网络用途、针脚表、线长和敷设环境。若要求PoE或其他供电，需单独定义回路与验证要求。 |
| Sample and link validation样品与链路验证 | Check termination, pairs, shield path and dimensions on the first article. Validate communication performance beyond continuity against the equipment and project requirements.首件核对端接、线对、屏蔽路径及尺寸；导通以外的通信性能按设备与项目约定验证。 |
APPLICATIONS连接的应用
Application directions应用方向
These connection directions concern equipment data interfaces. Confirm fit, circuits and performance from the actual equipment data.以下连接方向围绕设备数据接口展开，实际适配、回路与性能依据具体设备资料确认。
Controllers and industrial networks控制器与工业网络
Select cable construction from controller ports, network architecture and complete interface data. Confirm protocol and rate separately.依据控制器端口、网络架构和完整接口资料选择线缆结构；协议与速率另行确认。
Cabinet and panel data extensions机柜与面板数据延伸
Arrange data interfaces, length and strain support around rear-panel space. Keep ports and latches accessible.结合面板后方空间安排数据接口、长度和应力支撑，保留端口插拔与锁扣操作位置。
Links between network equipment网络设备间布线
Organize patching and routing around equipment ports. Define both link endpoints, pair mapping and shield grounding.按设备端口组织跳接与走线，明确链路两端、线对关系和屏蔽接地要求。
Robot-peripheral data interfaces机器人外围数据接口
Plan communication connections from peripheral-module ports. Review fixed and moving sections separately; cycle life needs exact cable and test evidence.按外围模块端口安排通信连接，固定与运动段分别审核；循环寿命需要具体线缆与试验依据。
Data links within automation cells自动化单元数据连接
Plan data paths between controllers and equipment modules. Check interfaces, route length and the equipment-defined communication validation.在控制器与设备模块之间规划数据路径，核对接口、布线长度及设备规定的通信验证方法。
Equipment service and network patching设备维护与网络跳接
Check both interfaces and pin definitions when replacing leads. Set patch length and labels for the port locations and validate the complete link.维护换线时核对两端接口和针脚定义，按端口位置安排跳接长度与标签，验证完整链路。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports custom equipment data-cable assemblies through wire harness manufacturing and OEM/ODM development. Complete interface data and circuit definitions guide materials, dimensions, samples and inspections before manufacture against approved documents.Super Smile-Tech 中国工厂围绕设备数据连接组件提供定制线束制造与 OEM/ODM 支持。从完整接口资料与回路定义开始，确认物料、尺寸、样品和检验要求，再按批准文件组织制造。
Both interfaces and complete part numbers两端接口与完整料号
Define the full family, orientation and mating parts for both ends, such as RJ45, IX or M12. A brand name does not define the interface.明确RJ45、IX或M12等两端接口的完整系列、方向与对插件，不以品牌名称替代接口定义。
Cable construction, length and shielding线缆结构、长度与屏蔽
Select pairs, impedance, shielding and length for the target link. Confirm complete-assembly capability with both devices.按目标链路选配线对结构、阻抗、屏蔽及长度，完整组件能力需结合两端设备确认。
Sample and link validation样品与链路验证
Check termination, pairs, shield path and dimensions on the first article. Validate communication performance beyond continuity against the equipment and project requirements.首件核对端接、线对、屏蔽路径及尺寸；导通以外的通信性能按设备与项目约定验证。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
Does a matching interface shape guarantee data compatibility?接口外形相同就能保证数据兼容吗？
No. Confirm the full family, pin and pair mapping, equipment communication, cable construction and actual link requirements.不能。还需确认完整系列、针脚与线对、设备通信方式、线缆结构和实际链路要求。
Does continuity acceptance establish network performance?导通合格是否代表网络通信性能合格？
No. Pairs, termination, impedance, shielding, length and both devices affect communication and need appropriate link validation.不能。通信还受线对结构、端接、阻抗、屏蔽、长度和两端设备影响，需要相应链路验证。
Does an RJ45 or M12 interface establish PoE capability?有RJ45或M12接口就可以承载PoE吗？
No. Confirm the power function, pin allocation, conductor and contact limits, temperature rise and equipment compatibility separately.不能。供电功能、针脚分配、导体与接点能力、温升及整机兼容需另行确认。
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the m12 to rj45 network harness. We can use them to review configuration and sample requirements.提供M12转RJ45网络线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。