MMI 2G HSD-LVDS Dual Right-Angle Display Harness can be configured around equipment interfaces and routing. Connector family, signaling method and cable impedance describe different parts of the link. A keyed housing is not proof of electrical compatibility.MMI 2G HSD-LVDS双弯头显示连接线束可围绕设备接口与安装路径进行配置。连接器系列、信号方式与线缆阻抗描述链路的不同部分，带防错键的壳体不等于电气兼容证明。
Use the mmi 2g hsd-lvds dual right-angle display harness form as a starting point and confirm these design points against drawings and the actual equipment.以MMI 2G HSD-LVDS双弯头显示连接线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Define signal type, pair allocation, shield continuity and termination as well as the connector shape. Establish transmission performance from the actual cable, length and system validation.在接口外形之外确认信号类型、线对分配、屏蔽连续性和端接方法；传输能力应按实际线材、长度及整机验证结果确定。
Distinguish FAKRA coaxial and HSD differential constructionFAKRA同轴与HSD差分结构必须区分
Check color coding together with mechanical keying颜色编码需与机械键位同时核对
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Exact FAKRA/HSD or LVDS interface seriesFAKRA/HSD或LVDS接口具体系列 | Use the exact FAKRA, HSD or LVDS series to define interfaces.准确FAKRA、HSD或LVDS系列决定接口结构。 |
|---|---|
| Keying, color coding and mating orientation键位、颜色编码和插合方向 | Check color coding, mechanical keying and gender together.颜色编码、机械键位和公母方向一起核对。 |
| Coaxial/differential construction, impedance and length同轴或差分线结构、阻抗与长度 | Configure coaxial and differential paths separately for impedance and length.同轴和差分路径按阻抗及长度分别配置。 |
| Camera, display or antenna function and tests摄像头、显示或天线功能及测试 | Use separate test boundaries for camera, display and antenna duties.摄像、显示或天线用途采用对应测试边界。 |
| Circuit and revision reference电路与版本依据 | Provide exact connector codes, cable specification, channel requirements, serializer/deserializer references and any power-over-coax conditions.请提供准确接头编码、线缆规格、通道要求、串行器与解串器型号，以及可能存在的同轴供电条件。 |
| Sample and manufacturing configuration样品与制造配置 | Confirm the complete channel, assembly geometry, sample checks and agreed RF or differential measurements before release.放行前确认完整通道、装配形状、样件检查及约定的射频或差分测量。 |
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
For display and imaging projects, first compare equipment generation, connectors, pins and signal definition, then confirm length and routing behind the panel. Use the exact FAKRA, HSD or LVDS series to define interfaces.显示与图像项目先核对设备代际、接头、针脚和信号定义，再确认线长及面板后布线路径。选配时，准确FAKRA、HSD或LVDS系列决定接口结构。
Check color, keying, bands and routing together. Check color coding, mechanical keying and gender together.颜色、键位、频段及安装路线共同核对。选配时，颜色编码、机械键位和公母方向一起核对。
Arrange ports and strain support within the device envelope. Configure coaxial and differential paths separately for impedance and length.端口排列与应力支撑结合设备空间设计。选配时，同轴和差分路径按阻抗及长度分别配置。
Define display/antenna duties and interfaces by device revision. Use separate test boundaries for camera, display and antenna duties.接口、显示或天线任务应按设备版本确定。选配时，摄像、显示或天线用途采用对应测试边界。
Review keying, fixing and coax transitions together. Use the exact FAKRA, HSD or LVDS series to define interfaces.机械键位、固定与同轴过渡一起审核。选配时，准确FAKRA、HSD或LVDS系列决定接口结构。
Similar connectors cannot replace protocol, pinout and compatibility review. Check color coding, mechanical keying and gender together.相近接头不能替代协议、针脚和兼容审核。选配时，颜色编码、机械键位和公母方向一起核对。
Our China factory supports fakra / lvds automotive cable projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕Fakra / LVDS汽车电缆的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Use the exact FAKRA, HSD or LVDS series to define interfaces.准确FAKRA、HSD或LVDS系列决定接口结构。
Check color coding, mechanical keying and gender together.颜色编码、机械键位和公母方向一起核对。
Use separate test boundaries for camera, display and antenna duties.摄像、显示或天线用途采用对应测试边界。
No. FAKRA describes a coaxial connector family, while LVDS describes signaling. Determine whether the equipment requires coax, HSD differential wiring or another interface.不是。FAKRA 描述同轴接头系列，LVDS 描述信号方式。应确认设备需要同轴、HSD 差分连接还是其他接口。
No. Confirm coding, contact interface, cable type and the electrical function on both sides. Color is an aid, not a complete specification.不代表。还需确认两端编码、接触界面、线缆类型和电气功能。颜色只是辅助识别，不是完整规格。
No. Protocol conversion requires compatible electronics. A cable adapter changes a physical connection and must preserve the required channel.不能。协议转换需要兼容的电子设备，线缆转接改变物理连接，并需保持所要求的通道特性。
Share mating interfaces, a circuit table, target lengths or a sample for the mmi 2g hsd-lvds dual right-angle display harness. We can use them to review configuration and sample requirements.提供MMI 2G HSD-LVDS双弯头显示连接线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。
