Branched end layout分支端头布局
Conductors separate toward different ends, creating individual connection points. Branch lengths and directions can follow the equipment modules.导线向不同端头分出，形成独立接入位置。各支路可围绕设备模块分别安排长度与方向。
Switch Cable Assembly开关电缆组件
Push Button & Microswitch Multi-Branch Harness按钮与微动开关多分支线束
Push Button & Microswitch Multi-Branch Harness combines branched end layout, switch connection end. Interface, circuit and installation data guide dimensions, material selection and sample review.按钮与微动开关多分支线束的结构重点包括分支端头布局、开关连接端。接口、电路与安装资料将作为尺寸、物料和样品制作的确认依据。
- Interface and circuit review接口与回路对应审核
- Length and installation configuration线长与安装结构定制
- Manufacture from approved sample样品确认后组织制造
CONSTRUCTION结构解析
Connection structure and design details连接结构与设计要点
Use the push button & microswitch multi-branch harness form as a starting point and confirm these design points against drawings and the actual equipment.以按钮与微动开关多分支线束的结构形式为起点，结合图纸和实际设备确认以下设计要点。
Switch connection end开关连接端
Leads connect at switch or button locations, with routing arranged for panel mounting, operation and rear wiring space.引线接向开关或按钮连接位置，布置时可兼顾面板安装、操作方向与背部接线空间。
Interface and function review接口与功能确认
Confirm NO/NC and momentary/latching actions separately常开常闭与自复位保持动作分别确认
Installation and acceptance安装与验收
Switch current ratings must match the load type开关标称电流需对应负载类型
CONFIGURATION结构与选配
Construction & customization options结构与定制配置
The table describes the construction and available configuration choices. Materials, dimensions, circuits and inspection requirements are agreed for each project.以下说明展示结构与可配置内容。具体材料、尺寸、电路和检验要求按项目确认。
| Switch model, contact form and wiring diagram开关型号、触点形式与接线图 | Define contacts, action and wiring from the switch model.按开关型号定义触点、动作和接线关系。 |
|---|---|
| Load type, inrush and switching requirements负载类别、浪涌与开断要求 | Review inrush and switching for motor, lamp or inductive loads.电机、灯具或感性负载分别核对浪涌与开断。 |
| Indicator supply, polarity and common terminal指示灯供电、极性和公共端 | Identify indicators, supplies and common terminals separately.指示灯、电源与公共端单独标明。 |
| Mounting cutout, leads and protection structure安装开孔、引线与保护结构 | Match cutout, leads and protection to the assembly.面板开孔、引线和防护配合实际装配。 |
| Circuit and revision reference电路与版本依据 | Provide the switch part number or sample, circuit and switch-state table, load type and ratings, terminal or mating-connector details, panel cutout, cable length and exit, environment, quantity and project-specific acceptance method.请提供开关料号或样品、回路图与状态表、负载类型和额定参数、端子或对插件资料、面板开孔、线长与出线、环境、数量及项目验收方法。 |
| Sample and manufacturing configuration样品与制造配置 | We review switch identity, contact schedule and cable termination before building the first article. The sample can then be checked for dimensions, terminal orientation, labels and continuity in each specified switch state.首件制作前审核开关身份、触点表和线缆端接。样品随后可按指定开关状态检查尺寸、端子方向、标识及导通。 |
APPLICATIONS连接的应用
Application directions应用方向
These are connection directions for project discussion. Suitability depends on interfaces, circuits, installation conditions and project validation; configuration can be adapted to the equipment.以下为可讨论的连接方向。实际适用性取决于接口、电路、安装环境和项目验证，可按设备需求调整。
Control-panel switches控制面板开关
Wire buttons, contacts and indicators from the panel circuit. Define contacts, action and wiring from the switch model.按钮、触点和指示灯按实际面板电路分开接线。选配时，按开关型号定义触点、动作和接线关系。
Equipment limits and controls设备限位与操作
Match NO/NC and latching/momentary action to equipment logic. Review inrush and switching for motor, lamp or inductive loads.常开常闭、保持或复位动作与设备逻辑匹配。选配时，电机、灯具或感性负载分别核对浪涌与开断。
Auxiliary load switching辅助负载开关
Lamp or motor inrush affects terminations and protection. Identify indicators, supplies and common terminals separately.灯具或电机负载的浪涌影响端接和保护。选配时，指示灯、电源与公共端单独标明。
Remote-switch contacts and service远端开关接点与检修
For remote controls, confirm contact construction, normally open or closed states and cable length before arranging accessible service connections. Match cutout, leads and protection to the assembly.远端控制先确认开关接点形式、常开常闭状态及线缆长度，再安排检修时可接近的连接位置。选配时，面板开孔、引线和防护配合实际装配。
Status-indication modules状态指示模块
Identify indicator power, common terminals and control contacts separately. Define contacts, action and wiring from the switch model.指示灯供电、电路公共端和操作触点分别标识。选配时，按开关型号定义触点、动作和接线关系。
Moving structures and limit interfaces移动结构与限位接口
Define limit connections from mechanical movement, contact states and safety-design requirements. The harness follows the approved circuit and interfaces. Review inrush and switching for motor, lamp or inductive loads.限位连接需结合机械动作、接点状态和安全设计要求定义，线束只按获批电路与接口制作。选配时，电机、灯具或感性负载分别核对浪涌与开断。
ENGINEERING & PRODUCTION工程与制造
Adapt the connection to your equipment.围绕设备，调整连接细节。
Touched by me, better it’ll beTouched by me, better it’ll be
Custom wire harness manufacturing in China中国工厂 · 定制线束制造
Our China factory supports switch cable assembly projects through custom wire harness manufacturing and OEM/ODM development. Interface, circuit and installation data guide material selection, sample builds and manufacturing-document approval before repeat production.Super Smile-Tech 中国工厂围绕开关电缆组件的项目需求提供定制线束制造与 OEM/ODM 支持。我们从接口、电路与安装资料开始，协同物料选配、样品制作和制造文件确认，再按批准要求组织重复生产。
Switch model, contact form and wiring diagram开关型号、触点形式与接线图
Define contacts, action and wiring from the switch model.按开关型号定义触点、动作和接线关系。
Load type, inrush and switching requirements负载类别、浪涌与开断要求
Review inrush and switching for motor, lamp or inductive loads.电机、灯具或感性负载分别核对浪涌与开断。
Mounting cutout, leads and protection structure安装开孔、引线与保护结构
Match cutout, leads and protection to the assembly.面板开孔、引线和防护配合实际装配。
PRODUCT QUESTIONS产品问答
Product & customization questions产品与定制常见问题
How are switch action and contacts confirmed?开关动作和触点应怎样确认？
Confirm NO/NC and momentary/latching actions separately常开常闭与自复位保持动作分别确认
Does a switch current rating apply to every load?开关电流是否适用所有负载？
Switch current ratings must match the load type开关标称电流需对应负载类型
Can illuminated-switch wiring be identified by pin count?带灯开关能按针数确定接线吗？
Do not guess illuminated-switch wiring from pin count带灯开关针脚不能按针数猜测
Start with your interface and installation requirements从您的接口与安装需求开始
Share mating interfaces, a circuit table, target lengths or a sample for the push button & microswitch multi-branch harness. We can use them to review configuration and sample requirements.提供按钮与微动开关多分支线束的对插接口、回路表、目标长度或参考样品，我们据此梳理选配与样品确认事项。